Herunterladen Inhalt Inhalt Diese Seite drucken

Intended Use; Safety Information - Scheppach HS105 Originalbetriebsanleitung

Vorschau ausblenden Andere Handbücher für HS105:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
• Central struts, long (2x)
• Rubber feet (4x)
• Assembly material

4. Intended use

The bench-type circular saw is designed for the slitting
and cross-cutting of all types of timber, commensurate
with the machine's size.
The machine is not to be used for cutting any type of
roundwood.
The machine is to be used only for its prescribed pur-
pose. Any use other than that mentioned is considered
to be a case of misuse. The user/operator and not the
manufacturer shall be liable for any damage or injury re-
sulting such cases of misuse.
The machine is to be operated only with suitable saw
blades. It is prohibited to use any type of cutting-off
wheel. To use the machine properly you must also ob-
serve the safety regulations, the assembly instructions
and the operating instructions to be found in this manual.
All persons who use and service the machine have to be
acquainted with this manual and must be informed about
its potential hazards. It is also imperative to observe the
accident prevention regulations in force in your area. The
same applies for the general rules of occupational health
and safety.
m Important!
When using the equipment, a few safety precautions
must be observed to avoid injuries and damage. Please
read the complete operating instructions and safety regu-
lations with due care. Keep this manual in a safe place,
so that the information is available at all times. If you give
the equipment to any other person, hand over these op-
erating instructions and safety regulations as well. We
cannot accept any liability for damage or accidents which
arise due to a failure to follow these instructions and the
safety instructions.
The manufacturer shall not be liable for any changes
made to the machine nor for any damage resulting from
such changes.
Even when the machine is used as prescribed it is still
impossible to eliminate certain residual risk factors. The
following hazards may arise in connection with the ma-
chine's construction and design:
• Contact with the saw blade in the uncovered saw zone.
• Reaching into the running saw blade (cut injuries).
• Kick-back of workpieces and parts of workpieces
• Saw blade fracturing.
• Catapulting of faulty carbide tips from the saw blade.
• Damage to hearing if essential ear-muffs are not worn.
• Harmful emissions of wood dust when the machine is
used in closed rooms.
m Please note that our equipment has not been de-
signed for use in commercial, trade or industrial appli-
cations. Our warranty will be voided if the machine is
used in commercial, trade or industrial businesses or
for equivalent purposes.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

5. Safety information

m Attention! The following basic safety measures must
be observed when using electric tools for protection
against electric shock, and the risk of injury and fire.
Read all these notices before using the electric tool and
keep the safety instructions for later reference.
Safe work
1 Keep the work area orderly
– Disorder in the work area can lead to accidents.
2 Take environmental influences into account
– Do not expose electric tools to rain.
– Do not use electric tools in a damp or wet environ-
ment.
– Make sure that the work area is well-illuminated.
– Do not use electric tools where there is a risk of
fire or explosion.
3 Protect yourself from electric shock
– Avoid physical contact with earthed parts (e.g.
pipes, radiators, electric ranges, cooling units).
4 Keep children away
– Do not allow other persons to touch the equipment or
cable, keep them away from your work area.
5 Securely store unused electric tools
– Unused electric tools should be stored in a dry, ele-
vated or closed location out of the reach of children.
6 Do not overload your electric tool
– They work better and more safely in the specified
output range.
7 Use the correct electric tool
– Do not use low-output electric tools for heavy work.
– Do not use the electric tool for purposes for which it
is not intended. For example, do not use handheld
circular saws for the cutting of branches or logs.
– Do not use the electric tool to cut firewood.
8 Wear suitable clothing
– Do not wear wide clothing or jewellery, which can
become entangled in moving parts.
– When working outdoors, anti-slip footwear is rec-
ommended.
– Tie long hair back in a hair net.
9 Use protective equipment
– Wear protective goggles.
– Wear a mask when carrying out dust-creating work.
10 Connect the dust extraction device if you will be
processing wood, materials similar to wood, or
plastics.
– If connections for dust extraction and a collecting
device are present, make sure that they are con-
nected and used properly.
– When processing wood, materials similar to wood,
and plastics. operation in enclosed spaces is only
permitted with the use of a suitable extraction system.
11 Secure the workpiece
– Use the clamping devices or a vice to hold the
workpiece in place. In this manner, it is held more
securely than with your hand.
– An additional support is necessary for long work-
pieces (table, trestle, etc.) in order to prevent the
machine from tipping over.
23 І 168

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

5901308901

Inhaltsverzeichnis