Proper Use; General Safety Instructions - Scheppach Hf50 Originalbetriebsanleitung

• Front pressure bar (9)
• Front pressure bar holder with screws (9a)
• Suction adapter (12)
• 2x Wooden push block
• Mitre gauge (10)
• Protective cover with alignment pin (13)
• 8x Allen screw M5 x 20 (m)
• 6x Allen screw M5 x 12 (l)
• 2x Allen screw M6 x 16 (g)
• 2x Hexagonal bolt M6 x 40 (c)
• 7x Coach bolt M6 x 20 (f)
• 3x Coach bolt M6 x 25 (d)
• 5x Coach bolt M6 x 35 (e)
• 2x Knurled screw M6 (a)
• 17x Washer Ø 6 (h)
• 14x Washer Ø 5 (n)
• 13x Knurled nut M6 (b)
• 2x Wing nut M6 (i)
• 2x Nut M6 (j)
• 8x Nut M5 (o)
• Allen key - size 4 (k)
• Open-ended spanner, size 18
• Open-ended spanner, size 24
• Table width extension mounting device (11)
• Tool receiver Ø 6 / 8 / 12
• Operating manual
• Allen key, size 5 (p)

4. Proper use

The machine is intended exclusively for the following
activities: Working with materials made of wood and
plastic, such as e.g.: Milling grooves, machining re-
cesses, copying curves and lettering within the spec-
ified machine limits. The milling machine must not be
used for working on metal, stone, etc.
The machine may only be used in the intended manner.
Any use beyond this is improper. The user/operator, not
the manufacturer, is responsible for damages or inju-
ries of any type resulting from this.
An element of the intended use is also the observance
of the safety instructions, as well as the assembly in-
structions and operating information in the operating
manual.
Persons who operate and maintain the machine must
be familiar with it and must be informed about potential
dangers.
In addition, the applicable accident prevention regula-
tions must be strictly observed.
Other general occupational health and safety-related
rules and regulations must be observed.
28 | GB
The liability of the manufacturer and resulting damages
are excluded in the event of modifications of the ma-
chine.
The machine may only be operated with original parts
and original accessories from the manufacturer.
The safety, operating and maintenance specifications
of the manufacturer, as well as the dimensions speci-
fied in the technical data, must be observed.
Please note that our equipment was not designed with the
intention of use for commercial or industrial purposes. We
assume no guarantee if the device is used in commercial
or industrial applications, or for equivalent work.
The device is intended for use by adults. Children un-
der the age of 16 may only use the device when su-
pervised. The manufacturer is not liable for damage
caused by improper use or incorrect operation.
Only use the device as described and for the specified
areas of application.
The device is not designed for commercial use. Any
other use or modification shall be deemed to be im-
proper use and could give rise to considerable risk of
accident. The manufacturer assumes no liability for
damage arising from inappropriate use.

5. General safety instructions

Attention! The following basic safety measures must
be observed when using power tools for protection
against electric shock, and the risk of injury and fire.
Read all these notices before using the power tool and
store the safety instructions well for later reference.
Safe work
1 Keep the work area orderly
– Disorder in the work area can lead to accidents.
2 Take environmental influences into account
– Do not expose power tools to rain.
– Do not use electric tools in a damp or wet en-
vironment.
– Make sure that the work area is well-illuminated.
– Do not use power tools where there is a risk of
fire or explosion.
3 Protect yourself from electric shock
– Avoid physical contact with earthed parts (e.g.
pipes, radiators, electric ranges, cooling units).
4 Keep other persons away
– Do not allow other persons, especially children,
to touch the power tool or the cable. Keep them
away from your work area.
www.scheppach.com