Scheppach MST305 Originalbetriebsanleitung Seite 36

• Before making the cut, check that no collision could
occur between the stop rail (5) and the saw blade (35).
• Tighten the set screw (16) again.
• Turn the locking knob (10) counter-clockwise and
pull the lower indexed position lever (11) upwards
with your index finger.
• Use the locking knob (10) to adjust the rotary table
(14) to the desired angle. The pointer (12) on the
rotary table (14) must match the desired angle on
the scale (13) on the fixed saw table (8).
• Turn the locking knob (10) clockwise to fix the rotary
table (14) in place.
• Make a cut as described in point 9.4.
9.6 0°- 45° mitre cut and rotary table 0°
(Fig. 1, 2, 5, 11)
Mitre cuts of 0° - 45° to the working surface can be
carried out to the left and right using the chop saw.
Attention! For bevel cuts (inclined saw head), the
moveable stop rail (5) must be fixed in the outer po-
sition.
• Loosen the locking screw (16) on the moveable
stop rail (5) and push the moveable stop rail (5)
outwards.
• The moveable stop rail (5) must be locked in a po-
sition far enough from the inner position that the
distance between the stop rail (5) and the saw blade
(35) is at least 5 mm.
• Before making the cut, check that no collision could
occur between the stop rail (5) and the saw blade (35).
• Tighten the set screw (16) again.
• Move the machine head (19) to the upper position.
• Fix the rotary table (14) in the 0° position.
• Loosen the locking screw (24) and tilt the machine
head (19) to the left with the handle (1) until the
pointer (23) points to the desired angle on the scale
(22).
• Retighten the locking screw (24).
• Make a cut as described in point 9.4.
9.7 0°- 45° mitre cut and rotary table 0°- 45° (Fig.
1, 2, 6, 12)
The chop saw can be used for mitre cuts of 0°- 45° to
the left and right of the work surface and of 0°- 45° to
the stop rail (double mitre cut).
Attention! For bevel cuts (inclined saw head), the
moveable stop rail (5) must be fixed in the outer po-
sition.
• Loosen the locking screw (16) on the moveable
stop rail (5) and push the moveable stop rail (5)
outwards.
36 | GB
• The moveable stop rail (5) must be locked in a po-
sition far enough from the inner position that the
distance between the stop rail (5) and the saw blade
(35) is at least 5 mm.
• Before making the cut, check that no collision could
occur between the stop rail (5) and the saw blade (35).
• Tighten the set screw (16) again.
• Move the machine head (19) to the upper position.
• Turn the locking knob (10) counter-clockwise and
pull the lower indexed position lever (11) upwards
with your index finger to release the rotary table.
• Use the locking knob (10) to adjust the rotary table
(14) to the desired angle (see also point 9.5).
• Turn the locking knob (10) clockwise to fix the rotary
table (14) in place.
• Loosen the locking screw (24) and use the handle
(1) to tilt the machine head (19) to the left to the de-
sired angle (see also point 9.6).
• Retighten the locking screw (24).
• Make a cut as described in point 9.4.
9.8 Restricting the cutting depth (Fig. 3)
• The cutting depth can be seamlessly adjusted with
the screw (27). To do so, loosen the knurled nut
on the screw (27). Set the desired cutting depth
by screwing in or unscrewing the screw (27). Then
retighten the knurled nut on the screw (27).
• Check the setting with a test cut.
9.9 Dust bag (Fig. 1)
• The saw is equipped with a dust bag (18) for chips.
• Squeeze the wings of the metal ring on the dust
bag (18) together and slide it over the discharge
port near the motor.
• The dust bag (18) can be emptied via the zip on
the underside.
9.10 Replacing the saw blade (Fig. 14 - 17)
Pull out the mains plug!
Attention! Wear protective gloves when changing
the saw blade! Danger of injury!
• Swivel the machine head (19) upwards.
• Loosen the screw (f) on the flange cover so that it
can move freely.
• Fold the saw blade guard (4) up sufficiently that
the recess in the saw blade guard (4) is above the
flange screw (34).
• With one hand, fit the Allen key (c) to the flange
screw (34).
www.scheppach.com