Exhaust Duct; Gas Connection - Truma Trumatic S 3002 P Einbauanweisung

Exhaust gas cowl
The heater is only approved when used with a roof
cowl. This must be installed vertically or with no more
than a 15 degree slope!
Fig. F: Position the roof cowl so that the duct (minimum
length 1.5 m, maximum length 3 m) can be routed direct from
the heater unit, sloping upward all the way to the cowl. A
1.5 metre long duct must reach a height of at least 1 metre.
The remain der of the duct to the roof cowl must be installed
more or less vertically.
Trumatic S 3002 (P)
Fig. E: Cut out an opening with a Ø of 60 mm at a centre dis-
tance of at least 55 mm from the side walls.
Trumatic S 5002
1. Fig. E: Cut out an opening with a Ø of 70 mm at a centre
distance of at least 60 mm from the side walls.
2 Fig. E: In the case of a double-skin roof, line the cavity with
wood or slide in a rolled circular sheet metal strip (20) of about
220 mm in length and 1 mm in thick ness, to stiffen the roof so
that when the screws are tightened it does not warp and stays
weatherproof.
3. Fig. E: Push the cowl through the roof from above and
fasten it on the inside with screw ring (21). Next, secure the
screw ring (21) with a screw (44).
Use the enclosed rubber sealing ring without further sealing
materials.

Exhaust duct

For the Trumatic S, only the Truma stainless-steel waste gas
pipe AE 3 or AE 5 with the Truma pipe sheath UR or UR 5
(APP) may be used, since the devices have only been tested
and approved in conjunction with these pipes.
Length of exhaust duct: min. 1.5 m, max. 3 m!
Fitting and bending the stainless steel duct and stretch-
ing open the O-ring are made considerably easier by using
"Biege-Boy" (part no. 30030-33000).
1. Connecting the exhaust duct to the heater:
Slide sealing plate (22) about 3 cm onto the exhaust duct
(with the claw pointing towards the heater exhaust outlet).
Slide on pressure ring (25). Stretch open O-Ring (23) and
carefully pass it over the cut edge of the duct. Then plug the
exhaust duct into the exhaust outlet as far as the stop.
Slide the O-ring, pressure ring and sealing plate to the exhaust
outlet. Twist on sealing plate (22) and fasten it securely by
tightening screw (24).
10
A new O-ring (23) must be fitted each time the ex-
haust duct is dismantled.
2. Slide insulating duct (41) onto the exhaust duct (it must
reach from the cowl to the rear wall of the installation box,
refer to fig. E + D).
3. Fig. D + E: Take the ducting up the wall with as few bends
as possible. Slide exhaust gas duct (40) into the cowl as far as
the stop and secure with self-tapping screw (28).
The flue gas pipe (40) with insulating duct (41)
must be ascending along its entire length and se-
curely and permanently installed using several clamps
(42), since otherwise a water pocket may form that will
prevent the flue gas from exiting freely.

Gas connection

Fig. A (e): The gas supply's operating pressure (30 mbar)
must be the same as the unit's operating pressure (see type
plate).
Fig. G: The gas supply pipe (32) must be connected using a
cutting ring screw fitting with an outer diameter of 8 mm at
the connecting piece (33).
The gas connection fitting on the heating appli-
ance must not be bent! When tightening the connec-
tion nipple, hold it carefully in place with a second wrench!
Route the ducting in such a way that the heater can be re-
moved for servicing work.
Make sure the gas lines are free of dirt, chips and such prior
to connecting!
A special duct for internal gas connection is available on re-
quest. It is screwed onto gas connection fitting (33) with an
elbow.
The gas system must accord with the technical and adminis-
trative provisions of the individual country of use (in Europe,
for example, EN 1949 for motor vehicles).
National regulations and rulings (in Germany, for example,
the DVGW worksheet G 607 for motor vehicles) must be
respected.
Heater casing
1. Fig. G: Push the handle connector (26), the piezo pressure
igniter (27) if applicable, and the integrated operating element
(51) for the Trumavent TEB fan into the cut-outs (take care to
respect right-hand or left-hand installation!). Close off any un-
occupied cut-outs with the closure cover (50).
For Trumatic S 3002 P only
Plug the earthing cable (34) to the pressure igniter (27) and
the earth contact (37) on the casing.
2. Press type plate (52) into the observation window opening
(note right-handed or left-handed installation!).
3. With integrated control panel (51) plug connecting cable
(53) of the Trumavent fan TEB into the control panel. Bend
back strap (54) on the installation box and insert connecting
cable (53).
For Trumatic S 3002 P only
Slide flat connector of ignition cable (38) on the connection
(36) on the piezo ignitor (27) and slide on insulation (43 – refer
to fig. A).