Operation - Scheppach Vc16 Originalbetriebsanleitung

5. Flip the container (2) and place it on the rollers (3).
8.3 Filter and filter bag (Fig. 1)
The product has the following filter and filter bag included
in the scope of delivery:
Paper filter bag (14)
• Dry vacuuming
Foam filter (15)
• Wet vacuuming
Note:
1. In order to fit/remove the filter and filter bag, remove
the container cover (5) as described under 8.1.
2. Always set down the container cover (5) with the top
facing downwards.
3. After you have assembled/removed the desired filter
and filter bag, reattach the container cover (5) to the
container (2).
8.3.1 Fitting/removing the paper filter bag
(14) (Fig. 5)
Removing:
1. Remove the paper filter bag (14) from the bar (4a) on
the suction connection (4).
Assembling:
1. Attach the paper filter bag (14) to the bar (4a) on the
suction connection (4) inside the container (2).
2. Check that the paper filter bag (14) is installed correct-
ly and the sealing ring (14a) fully envelopes the bar
(4a) on the suction connection (4).
8.3.2 Fitting/removing the foam filter (15)
(Fig. 6)
Removing:
1. Remove the foam filter (15) from the filter cage (8).
Assembling:
1. Remove the foam filter (15) over the filter cage (8).
2. Check that the foam filter (15) is installed correctly
and fully envelopes the filter cage (8).
8.4 Connecting the suction hose (9)
8.4.1 Suction function (Fig. 7)
1. Push the hose coupling (9a) fully into the suction con-
nection (4).
2. Turn the hose coupling (9a) clockwise until it fully en-
gages.
3. Check that the suction hose (9) is installed correctly
by gently pulling on the hose coupling (9a).
8.4.2 Blast function (Fig. 8)
1. Push the hose coupling (9a) fully into the blowing con-
nection (7).
2. Turn the hose coupling (9a) clockwise until it fully en-
gages.
3. Check that the suction hose (9) is installed correctly
by gently pulling on the hose coupling (9a).
20 | GB
8.5 Uncoupling the suction hose (9)
(Fig. 6, 7)
Uncouple the suction hose (9) from the suction connec-
tion (4) or the blast connection (7):
1. Turn the hose coupling (9a) counter-clockwise.
2. Pull the hose coupling (9a) out of the suction connec-
tion (7) or the blowing connection (4).
8.6 Store nozzles (12/13), suction hose
(9) and suction pipes (11) (Fig. 3)
1. The nozzles (13/14), the suction hose (9) and the suc-
tion pipes (11) can be stored in the holders (5a) on the
container cover (5).
2. You can store the cable on the holder on the blowing
connection (7).
8.7 Attaching the suction pipe (11)
(Fig. 9)
1. Attach a suction pipe (11) to the handle (10).
Connect the suction pipe (11) at the desired length.
8.8 Using the various nozzles (12/13)
(Fig. 8)
Floor nozzle (12):
• Vacuuming of solid materials and liquids on medium
to large surfaces, carpets or floor mats.
• The floor nozzle (12) can be attached directly to the
handle (10) or the suction pipe (11) and used.
• If required, it can also be used without the extensions.
Joint nozzle (13):
• Vacuuming of solid materials and liquids in joints, cor-
ners, radiators and hard-to-reach areas.
• The joint nozzle (13) can be attached directly to the
handle (10) or the suction pipe (11) and used.
8.8.1
1. Insert the desired nozzle (12/13) into the handle (10)
or the suction pipe (11).
2. Remove the nozzle (12/13) by pulling it forward from
the handle (10) or suction pipe (11).
9

Operation

Please refer to the following descriptions for the function
of the controls.
ATTENTION
Always make sure the product is fully assembled
before commissioning!
WARNING
Danger of injury!
Do not insert the mains plug into the socket until you
are ready to use the product.
www.scheppach.com
Fitting the nozzle (Fig. 8)