System Connections - Onkyo R-100 Bedienungsanleitung

Precautions
I. Warranty Card
Theserial n umber i s written ontherear panel o fthisunit.Copy
theserial n umber a nd model n umber ontoyourwarranty c ard
and keepit in a safe place.
2. Recording Copyright
Recording o f copyrighted material forother t hanpersonal use
is illegal w ithoutpermission o fthecopyright holder.
3. AC Fuse
Thefuseislocated insidethechassis andisnotuser s erviceable.
if power d oes notcome on,contact your O nkyo s ervice center.
4. Care
From timeto timeyoushould wipe offthefrontandrear panels
andthecabinet W ithasoftcloth.Forheavier dirt,dampen a soft
clothin a weaksolutionof milddetergent andwater, w ringit
outdry,andwipeoff the dirt.Following t his,dryimmediately
Witha clean cloth. Donotuse rough material, thinners, alcohol
or otherchemical solvents orcloths since these coulddamage
the finish or remove the panellettering.
5. Power
WARNING
E BEFOR TURNING ONPOWER F OR THEFIRST T IME, R EAD
THE FOLLOWINGSECTIONCAREFULLY.
• Some models a redesigned f oruse onlywiththepower s upply
voltage of theregionwhere theyaresold.
European models.
(except U.K.):
U.K. & Australian models:
Worldwide models:
• Voltage Selector (Rear Panel)
Worldwidemodelsareequipped with avoltage selector t o
conform withlocalpower supplies. Besure to setthisswitch
to match thevoltageofthepower s upply inyourarea before
turning thepower s witch on.Voltage ischanged bysliding the
e groov inthe switch withascrewdriver
Confirm thattheswitchhas been moved a llthewaytotheright
or leftbeforeturning the powerswitchon. Models withouta
voltage selector canonlybeused in areas w here thepower
supplyisthe sameasthatof the unit.
120V
220V
at ACI 20V
• Tuning StepFrequencySwitch (RearPanel)
Worldwide m odels a reequipped w ithaswitch thatcontrols t he
AM(9kHz/I OkHz) and FM(50kHz/200kHz)
Besureto setthis switchto match thetuningStep frequency
in your area.
1OkHz/200kHz
U.S.A. and Canada
9kHz/50kHz
Other area
Systemconnections
General
Switch thepower b utton offbefore p erforming connections.
besure toperform leftand right c hannel connections
AC Outlets
• SWITCHED:
These outlets areswitched onandoff bythepower b utton on
thefrontpanel andremote control transmitter.
100 watts.
AC220V, 50Hz
AC 240V, 50Hz
120 and 220V switchable,
50/60Hz
totheright o rleft.
120V
220',' n.
at AC220V
band t uning steps.
Also
properly.
The capacity is
FM Antenna Connections
usethe T-shaped antenna ifyouliveinanarea where signal strength
of FM broadcasts is high. Connectthe antennato the FM75 ohms
terminals a ndplace the antenna on a wallor othersurface inthe
position in which reception i sbest.If signal strength i slowinyour
area, u seamufti-element FMoutdoorantenna. Consult y ourOnkyo
authorized servicecenteraboutthe right type of antennafor your
area.
NOTES:
1. DOnot connectboth the indoor T-shaped antennaandan
outdoor FM antenna. I f you decideto installan outdoor
antenna, b esureto disconnect t he indoorT-shaped antenna.
2. DOnot usethe sameantennafor both FM andTVreception
sincethe FM andTV signalscaninterferewith eachother.
If youmust u seacommon F M/TV antenna, use adirectional
linkage type splitter.
Directional
type splitter
To receiver
AM Antenna Connections
AnAMloopantenna i sincluded i ntheinstallation instructions bag.
Takeout the connectionline and connectit to the AM antenna
terminals. Thisloopantenna canbeplaced ontop of anystable
surfaceor attachedto a wall. Tryseveral p ositionsto determine
whichgives the bestreception. Besurethe antenna isnot neara
speaker. power c ord, t elevision s et, V CR or motorized appliances.
Whenusinganexternal AM antenna, donot remove the loopan-
tenna; c onnect b othantennas t o the AM antenna terminals.
AM loop antenna assembly
Rernove the vinyl tie and
take out the connection
a. With the antenna on
top of any stable surface
Mount
b. With the antenna
attached to a wall
Installation
Mount on a wall. etc.
NOTE:
AMreception i seasily a ffected b ytelevision s ets andVCRs.
Therefore, AM reception maybepoorif this unit is piaced too
close to a TV or a VCR.
linkage
To TV (or VCR)
Connect to the AM
antenna terminals.
Bend in the reverse
direction.
hole