Numark DCUSB Kurzbedienungsanleitung Seite 4

Zuletzt drehen Sie das Gegengewicht (und den Skalenring)
4.
entgegengesetzten Uhrzeigersjnn (zum Schwenkpunkt
gewünschte Gewicht erreicht ist. Falls die Skala sich mehr als 360
Grad über den Nullpunkt hinaus dreht, sollte der angezeigte
Wert des Skalenrings zu 3.5 dazu addiert werden.
*Das mitgelieferte Headshell und das Tonabnehmersystem
erfordern mindestens 3, jedoch höchstens 5 Gramm für
optimale Leistung.
Einstellung des Anti-Skate
In den meisten Fällen sollte das Anti-Skate
Wert eingestellt werden. Anti-Skate gleicht
Kräfte aus, welche bei manchen Tonabnehmer
wenn sich die Abtastnadel auf die Plattenmitte
Plattenspieler während Back-Cueing und Scratching
auf die Zentralspindel außergewöhnlich starkes
versuchen Sie das Anti-Skate in den auf
Schritten zu erhöhen. Fangen Sie mit einer
testen Sie das Verha)ten, dann steigern Sie es weiter, und so fort.
6
im
hin) bis das
ke sure all items listed on the front of this guide are included in Tie box.
neue
AD SAFETY
G? to http://www.numack.com
GENERAL CONTROLS
i.
Power Cable;
cable should be plugged into
a wall receptacle
audio connections
2. RCA Audio Output
These cables
plugged into
auf seinen minimalsten
inputs of your home stereo
system. (Please
nach innen gerichtete
Can still copy records to your
Systemen auftreten,
computer, even if the audio
outputs Of the turntable
zubewegt. Falls beim
not Connected
system. It is also possible to
beim Zubewegen
hear your records
"Skipping" auftritt,
your computer,
you have configured your
der Anzeige gezeigten
computer's sound input and
output options
Steigerung von 1 an,
enabled
Playthrough in the Audacity
software. *casc
Software Guide
information On configuring
your computer
audio from the turntable.
IMPORTANT:
switch on the bottom
next to the RCA cables that selects between PHONO/UNE. use PHONOlevel for plugging into a turntable input on
a home stereo. Use the LINE level for plugging into CD/AUX/TAPE inputs. WARNING: You may damage your
receiver if you plug in a LINE level into a PHONO input.
3. USB Audio Output:
software instruction
4. Power Button:
Platter: This platter
found on the dnvc ring underneath the platter. See SETUPINSTRUCTIONS for detailed information on installing
the Motor Drive
Start/Stop Buttons:
they seem to noz be function.ng, check to make sure that the Motor Drive Belt is property installed in the SETUP
INSTRUCTIONS,
7. Target Llght and Power Jack: This aluminum light can be rotated depending on the head Shell position and the
amount of light required
8. 33 and 45 RPM Buttons: These buttons control the RPM Of the turntable platter. A red LED indicates which RPM
mode has been selected.
NOTE; the turntable is powered down while in the 45 RPM setting, it will return to 33 RPM when it is powered
up.
Note: You can record your 78RPM records by recording them at 33 or 45rpm, then changing them to 73 in the
Audacity software.
9. Pitch LED: This LED illuminates green when the pitch slider is set at
from zero, the LED illuminates
10. Pitch Slider: This slide control allows the pitch to be increased or decreased by 10%. In the center position the
pitch is at 0%. When moved away from the center and towards the tone arm decreases the pitch (slows down the
ptatter) and moving the pitch slider away from the tone arm increase the pitch (speeds up the platter.)
TONE ARM: Items
details on these
11. Counter Weight and Scale Ring: The Counterweight is used to balance the head shell and cartridge assembly so
that the proper amount Of Stylus pressure is applied to the record.
12. Anti-Skate Adjustrnent:
more details.
13. Arm Clip: This specially designed arm clip secures the tone arm while at rest or when not in use. The arrn clip has
been designed to remain in the up position while unlocked.
NOTE: When transporting the turntable, it is always recommended that the headshe/l be removed and the arm Cllp
secured to prevent tonearm or turntable damage.
14. Tone Arm Lock Nue This Aluminum nut is used to secure the head shell and cartridge assembly to the tone arm
tube. See Cartridge Setup for more details.
15. Cartridge and Headshelt:
replaceable and compatible with a variety cf standard cartridges. Be sure to remove the clear plastic cover before
operating the turntable
(ENGLISH) QUJCK START
INSTRUCTION BOOKLET BEFORE USING THE PRODUCT
for product registration.
This power
AFTER all
are made.
cables:
Should be
the eudio
note: you
4
6
are
to a Stereo
through
as tong as
correctly and
Software
see the
for more
9
to play the
6
- 10
There is a
panel,
Use the included LISB Cable to connect your turntable to your computer, Refer to the
guide before plugging in your turntable.
This ring around the pawer button illuminates red when the turntable is switched on.
must be securely fastened to the turntable prior to operation. The Motor Drive Beit can be
Beit.
These buttons start and stop the turntable motor. Both buttons have the same function.
on the vinyl record surface.
When the pitch Slider is moved away
red,
11 — 15 are parts ot the tonearm. Refer to the TONEARM SETUP section
controls.
This knob is used to compensate for inward tracking forces. See TONEARMSETUP for
The cartridge is pre-mounted on a standard headshell. The cartridge is user
from the cartridge.
7
11
12
13
14
If
for additional