Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Please unfold page 5. Then you can always see the
operating elements and connections described.
Contents
Operating Elements and Connections . . . 9
1
1.1
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.2
Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Safety Notes . . . . . . . . . . . . . . . . . . . . . . . . 10
2
Applications . . . . . . . . . . . . . . . . . . . . . . . . 10
3
3.1
Approval . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Setting into Operation . . . . . . . . . . . . . . . . 10
4
4.1
Placing the transmitter and the receiver . . . 10
4.2
Connecting the units . . . . . . . . . . . . . . . . . . 10
4.2.1
Surveillance camera . . . . . . . . . . . . . . . . . 10
4.2.2
Microphone . . . . . . . . . . . . . . . . . . . . . . . . 10
4.2.3
Motion detector . . . . . . . . . . . . . . . . . . . . . 10
4.2.4
Power supply . . . . . . . . . . . . . . . . . . . . . . 10
4.3
Making adjustments . . . . . . . . . . . . . . . . . . . 11
4.3.1
Selecting channels . . . . . . . . . . . . . . . . . . 11
4.3.2
Activating the coding . . . . . . . . . . . . . . . . . 11
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5
Specifications . . . . . . . . . . . . . . . . . . . . . . 11
6
1 Operating Elements and Connections
1.1 Front panel
1 Power switch
2 Power LED
3 Push-button "switching channel" for manual acti-
vation of the control channel
4 Rigidly mounted antenna
(do not scratch or break off)
5 Buttons "+" and "-" to adjust the transmission
channels 1 – 5;
the adjusted channel is displayed in the window
(no signal is transmitted if the channel is set to 0 or
6 – 9)
6 Trimming control "trigger" to adjust the operating
time (approx. 1 second to 4 minutes) after detec-
ting a movement in the camera picture in case of
activated temporary operation
7 Selector switch for the operating mode
cont.
continuous operation [transmitter is
permanently switched on]
time
temporary operation [transmitter is
automatically switched on for the dura-
tion adjusted with the control "trigger"
(6) upon detection of a movement in the
camera picture]
8 Switch "moving detector" to activate the internal
motion detector
9 Selector switch for video polarity
normal
standard adjustment for positive pola-
rity
scramble negative polarity for coding the camera
picture
1.2 Rear panel
10 3.5 mm jack "trigger" to switch on the transmitter in
temporary operation [switch (7) in position "time"]
by an AC voltage between 1 and 24 V~ or by
short-circuiting the contacts
11 3.5 mm jack "switching channel" to activate the
control channel by an AC voltage between 1 and
24 V~ or by short-circuiting the contacts
Caution! The push-button "switching channel" (3)
is connected to this jack. When actuating the but-
ton, a voltage applied to the jack is short-circuited!
12 Phono input jack "audio A" to transmit an audio
signal (line level 500 mV)
13 Phono input jack "audio B" to transmit a second
audio signal, e. g. in case of a stereo signal (line
level 500 mV)
14 BNC input jack for the video signal to connect a
camera
15 Low voltage jack for the power supply with 12.8 –
15 V /250 mA;
centre contact = positive pole
required low voltage plug 5.5/2.1 mm
(outside/inside diameter)
9
Werbung
Inhaltsverzeichnis
