Werbung
Safetyinstructionsfor ERSA
It is only possible to work safely with this heating tool by reading the corresponding operating and safety
instructions in their entirety and following them to the letter.
0.
Application
Thewarrantyissuedby the manufacturer a ndany liabilityclaimsagainstthe manufacturer s hallbe renderednull
and void if the device is used in a manner not in accordancewith its designateduse or if alterations are madeto it.
1.
Check all components before use.
Haveany damagedparts repairedby a specialistor the manufacturer.Incorrectlyperformedrepairsrepresent
a risk of accidents for the user. Always use genuine ERSAspare parts for any repairs.
2.
Heating tools get hot.
Beforeheatingupthe device,checkthat the tool insert (e.g.solderingtip, modellinginsert, etc.) is correctly
connectedto the heatingtool. Do not allow the hot tool insert to touch your skin, your hair or any materials
which are heat-sensitive and flammable.Alwayswork on a basewith adequateheat-resistantproperties.
3.
Restrict
unauthorised
Makesurethat no-one,in particularchildren,can get nearheatingtool without your permission.
4.
Danger of fire!
Before heating up the heating tool, remove flammable objects, liquids and gases from the areawhere you will
be workingwith your heatingtool. Wheneveryou takea breakfrom your work, placethe heatingtool in the
holderprovidedfor that purpose.Disconnectyour heatingtools from the mains after use (this does not apply
to non-electricallyoperateddevicessuch as gas-operatedheatingtools).
Never leave your hot heating tool unattended.
5.
Rememberthat the tool insert needsa certain amount of time to cool down to a safe temperature even
after you have switched the device off.
Keepyour workplace tidy. An untidy workplaceincreasesthe risk of accidents.
6.
7.
Lead alloyed solders are toxic.
Solderscontainingleadaretoxic if they enteryour system.Forthis reason,it is strictly forbiddento eat,drink
or smoke. Byequalmeasure,you should thoroughlywashyour handsafter workingwith leadalloyedsoldec
8.
Dispose of waste solder in a responsible fashion.
Comply with your local authority's waste disposal regulations when disposing of the by-products of your
soldering work.
9.
Ventilation
and extraction
The materials and ancillary substances you use whilst soldering can have a detrimental effect on your health.
Makesurethere is adequateventilationor extraction.Complywith the relevantsafetydatasheets.
10.
Protectconnectioncables. (Thisdoes not apply to non-electricallyoperateddevicessuch as gas-operated
heatingtools). Do not usethe connectioncableto pull out the plug or as a meansof carryingthe device.
Makesure that connection cablesare not exposedto heat and do not come into contact with oil or sharp edges.
Damagedconnection cables represent a potential cause of fire, short-circuits and electric shocks.
11.
Take account
of ambient
Protectyour device against all liquids and moisture. Failureto do this representsa risk of fire or electric shocks.
12.
Look after your heating tool.
Always keepyour ERSAproduct in a safe, dry place out of the reachof children. Payattention to any maintenance
requirements. Checkyour deviceat regular intervals.Always usegenuine ERSAaccessoriesand spare parts.
13.
National and international regulations
Comply with national and international regulations governing health and safety at work.
ERSALöttechnik GmbH• Leonhard-Karl-Str. 24 • 0-97877 Wertheim, Germany • Phone +49 (0) 9342/800-0
access.
conditions.
heatingtools
Werbung
