Herunterladen Diese Seite drucken

2N IP style Bedienungsanleitung Seite 2

Vorschau ausblenden Andere Handbücher für IP style:

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 6
Product
Introduction
Read this manual carefully
before
herein. Refer to wiki.2n.cz
for complete
The
IP Style is a 2N IP intercom
support
for Bluetooth
and NFC technologies
the call, so-called
Face Zooming.
access
management.
The
intuitive
selected
destination.
The
version
with a secure combined
Installation
requirements
LAN connection,
UTP cable CatS or higher
POE+ 802.3at
or 12 V DC / 4 A power supply
Completed
installation
of the chassis (order
no. 9157001)
for flush
mounting.
Mechanical
Installation
The
device
is designed
for
surface
It is anticipated
that installation
the flush mount
box has been completed
the required
cables
have
been
connection.
Recommended
length of prepared
30
cm.
Unscrew
the
connector
cover
device.
Thread
all
of the
cables
(terminals
or end pieces, etc.) through
the inside of the connector
cover. After threading
cables
through
the bushing,
fit the
Fold out the mounting
bracket
Of the
chassis
Or flush
mount
device has profiles
which
are fitted
bracket
and slid
down
to the
Electrical
installation
Description
Of terminals,
connectors
CONTROL
POWERLED
LAN
VBUS
INI, IN2, IN3
Terminals
TAMPER
SWITCH
OUT
Terminals
RELAY
POWER 12 V / 4 A
LAN
connector
Tamper
Switch
SD
CARD
Connection
Of a lock
Connect
the electrical
lock directly
low-consumption
locks
and
keep
Installation
security
If the device is installed
in a location
recommend
use of a
Security
Factory
Default
Resetting
- Follow
Disconnect
the device from the power supply.
Press
and
hold
the
CONTROL
Connect
the device to the power supply.
Keep holding
the button
DO not touch
the display
using the product
and follow
user documentation.
of the very highest
quality
as well as a Full HD camera
The 2NR IP Style allows you to control
touchscreen
display
allows
IP Style
is available
in a version
card reader (order
no. 9157101-S) with frequencies
with an RJ-45 connector
no. 9157002)
or flush
mounting.
Of the chassis or
and all of
laid and are
ready
for
cables
on
the
back
of
the
with
no
connectors
the bushing
on
the
required
end
pieces.
located
at the bottom
box.
The
back
Of the
into the mounting
lowest
possible
position,
and available
components
Button
for restoring
factory
settings
Device
status
LED
LAN
connection
status
LED
Connector
for
connection
of a bus
Grounding
terminal
Input terminals
in passive / active
OFF
open contact
OR UIN > 1.5 V
ON = closed
contact
OR UIN < 1.5 V
for connection
of the device to a security
Active output
12 V / 0.6 A DC
for 30 V / 1 A AC/DC
Terminals
for external
12 V / 4 A DC power supply
Optionally
POE+ 802.3at
for connection
Switch
detecting
unauthorized
SD card
slot
to the active output
of the device.
the
limits
mentioned
above.
where there is a danger
relay
(order
no. 9159010)
the instructions
below
button.
for a few seconds
and then release it.
during
restart,
it is being calibrated.
the instructions
and recommendations
with a 10" touchscreen
display,
with a function
the entrance
area and perform
visitors
to easily
search
the
with
a combined
card
reader
of 125 kHz and 13.56 MHz.
for surface
mounting,
or a flush mount
anchoring
the
device
by snapping
Connect
all Of the cables to the device.
bracket
provides
sufficient
support
the cabling
so it is not
necessary
In any
way.
After
connection
and securing
the clips,
screw
the
connector
in the
device
towards
the
chassis
box and then press in a downwards
the installation.
Then all you have to do is lock the
position
by tightening
the
two
using an Allen key.
Graphical
illustration
Of installation
end of this
short
manual.
mode (—30 V to +30 V DC)
system
NO/NC
contact
of the device
to the LAN
opening
of the
device
In any case, you are recommended
of unauthorized
tampering
with the device, we strongly
to ensure
the
maximum
security
to reset the factory
default
values:
included
card reader, with
for facial monitoring
during
remote
phone
book
and call the
(order
no. 9157101)
and a
box (order
it into
place.
The mounting
when connecting
to support
the
device
of superfluous
cabling
in
cover
back
on and
fold
or
the
flush
mount
direction
to seal
screws
inside
the
device
can be found
at the
to use
of the
installation.
2

Werbung

loading