Scheppach 5906706901 Originalbetriebsanleitung Seite 30

If you are not sure whether working conditions are safe
or unsafe, do not work with the machine.
90° cuts (Fig. 6 - 7)
1. Loosen the star screw (C).
2. Set the transverse cutting gauge (6) to 90° and
re-tighten the star screw.
3. Tighten the wing screw (D) to fix the transverse
cutting gauge (6) into position. (Fig. 6)
4. Use the handle (11) to push the machine head (1)
backwards.
5. Place the tile on the stop rail (7) on the transverse
cutting gauge.
6. Use the handle (11) to push the machine head (1)
to the required cutting depth and fix the machine
head again.
7. Switch on the tile cutter. Attention: Wait until the
cooling water has reached the cutting wheel (10).
8. Use the handle (11) to pull the machine head (1)
slowly and evenly forwards through the tile.
9. Switch the cutting wheel off again once you have
finished cutting.
45° diagonal cut (Fig. 8)
1. Set the angled stop (6) to 45°
2. Perform cutting as described above.
45° longitudinal cut (Fig. 9)
1. Loosen the star knob screw (E) on both sides
2. Angle the guide rail (8) 45° to the left on the angle
scale (17).
3. Re-tighten the star knob screw (E) on both sides.
4. Make the cut as described.
Replacing the diamond cutting wheel (Fig. 10 - 12)
Attention! Pull out the mains plug
1. Unscrew the screw (F) and remove the cutting
wheel guard (9). (Fig. 10)
2. Attach the Allen key (19) to the motor shaft and hold.
3. Use the spanner (20) to unscrew the flange nuts in
the direction in which the cutting wheel (10) runs.
(Left-handed thread)
4. Remove the outer flange (21) and the cutting
wheel (10).
5. Clean the holding flange carefully before installing
the new cutting wheel.
6. Insert the new cutting wheel in the reverse se-
quence and tighten.
7. Attention: Ensure that the cutting wheel runs in
the correct direction!
8. Re-install the cutting wheel guard (9).
30 | GB
Adjusting the parallelism of the diamond cutting
wheel (Fig. 13 - 15)
If the cut is not straight or the tile breaks along the cut-
ting line, the parallelism of the diamond cutting wheel
must be adjusted.
1. At the beginning, the stop rail must be set at right
angles to the guide rail. To do this, loosen the two
hexagon socket screws (A) of the stop rail and
align it squarely with a large right angle or tile.
2. To do this, the diamond cutting wheel must run
along the edge of the angle or tile for its entire
length. Then retighten the two hexagon socket
screws (A) of the stop rail.
3. Disassemble the length indicator by removing both
Phillips screws (B). (Fig. 16)
4. Disassemble the cable fixing (C). (Fig. 17)
5. Slightly loosen two hexagon nuts (D) of the saw
unit on each side. (Fig. 18, 19)
6. Now the complete sawing unit with diamond cut-
ting wheel can be aligned to the stop rail using a
right angle or a large tile. (Fig. 20)
7. Tighten the hexagon nuts of the saw unit again and
reassemble all machine parts. Check the parallel-
ism and make a test cut.
If the test cut is still not satisfactory, carry out points
1 - 6 again.
10. Electrical connection
The electrical motor installed is connected and ready
for operation. The connection complies with the appli-
cable VDE and DIN provisions.
The customer's mains connection as well as the exten-
sion cable used must also comply with these regulations.
Damaged electrical connection cable
The insulation on electrical connection cables is often
damaged.
This may have the following causes:
• Pressure points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been improp-
erly fastened or routed.
Places where the connection cables have been cut due
to being driven over.
• Insulation damage due to being ripped out of the wall
outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insulation
damage.
www.scheppach.com