Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Signal strength status (four levels)
5
Battery status (empty, almost empty, medium, full)
6
Detergent level (1 / 2 / 3)
7
Supplied screws and dowels
Illustration D
Stand dowels (2 pieces)
1
Screw 4x22 (2 pieces)
2
Screw 4x16 (10 pieces)
3
Installation
For the illustrations, refer to the graphics page.
Fit the supplied loose parts onto the device before start-
ing up the device.
Have the included screws and the appropriate screw-
driver ready.
Fitting the wheels
1. Insert the wheels.
Note
Pay attention to the alignment of the hole.
Illustration E
2. Secure the wheels with 1 screw each.
Mounting the stand
1. Insert the stand.
Illustration F
2. Insert the 2 dowels into the holes as far as they will
go.
3. Secure the base with 2 screws.
Mounting the storage for spray lances
1. Hook in the storage for the spray lances.
2. Secure the storage with 2 screws.
Illustration G
3. Secure the cover with 4 screws.
Illustration H
Mounting the transport handle
1. Attach the transport handle.
Illustration I
Mounting the accessory net
1. Hang the accessory net on the hooks.
Illustration J
Push the high-pressure hose through the
hose guide
1. Insert the high-pressure hose through the hose
guide from the rear.
Illustration K
Installing the water connection coupling
1. Screw the water connection coupling onto the water
connection on the device.
Illustration L
Initial Start-Up
Note
If you do not want to control the device by mobile device
®
via a Bluetooth
connection, you only have to follow the
steps in the section "Connecting the high-pressure
gun".
Download the app and register your device
1. Download the KÄRCHER Home & Garden app (see
chapter KÄRCHER Home & Garden app).
2. Start the KÄRCHER Home & Garden app.
16
3. Log in to the KÄRCHER Home & Garden app. If
necessary, create an account for this.
4. Scan the enclosed QR code.
The high-pressure cleaner is registered.
Note
If you do not have the enclosed QR code at hand, you
can also register the device with the part number and
serial number. Both numbers are given on the type
plate.
5. Follow the instructions of the KÄRCHER Home &
Garden app.
Note
Be sure to do this before connecting the high-pressure
®
gun Bluetooth
Activate on your mobile device.
Connecting the high-pressure gun
Note
You can find a detailed description of the connection at
https://www.kaercher.com/FCR.
6. Plug the mains plug for the high-pressure cleaner in-
to a socket.
The device switches to coupling mode for 60 s. Dur-
ing this time it is possible to couple the high-pres-
sure gun.
7. Press the "+" key and the "-" key on the high-pres-
sure gun simultaneously for at least 3 s.
If the coupling is successful, the pressure levels, as
well as the radio and the Bluetooth
shown on the display.
Illustration M
The Bluetooth
vice and the high-pressure cleaner is established
automatically.
Note
If necessary, you can also establish the Bluetooth
nection at a later time by pressing the "-" key for 10 s.
8. If the coupling attempt failed:
a Pull the mains plug for the high-pressure cleaner
out of the socket.
b Wait 20 s.
c Couple the high-pressure gun again.
1. Place the device on a level surface.
2. Completely unwind the high-pressure.
3. Pull the high-pressure hose completely forward
through the hose guide and eliminate any loops and
twists.
4. Insert the high-pressure hose into the high-pressure
gun until it audibly clicks into place.
Note
Take care to ensure the correct alignment of the nipple.
Illustration N
5. Check the secure connection by pulling on the high-
pressure hose.
6. Plug the mains plug into a mains socket.
For the connection values, see the type plate or chapter
Technical data.
Observe the water distribution company regulations.
ATTENTION
Damage through contaminated water
Contamination in the water can damage the pump and
the accessories.
KÄRCHER recommends using the KÄRCHER water fil-
ter for protection(special accessory, order number
4.730-059).
English
®
symbol, will be
®
connection between the mobile de-
Initial startup
Water supply
®
con-
Werbung
