Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Writing Sub Codes
Erasing Sub Codes
INPUT
AMS
REW
=
+
0
ANALOG OPT
COAXIAL
SELECT
DATA
STOP
PLAY
POWER
p
"
1
Set ID MODE to the position for the type of ID
you want to erase.
2
To erase a start ID or skip ID
Press ERASE when the ID you want to erase
appears in the display.
"(ERASE)" appears in the display as the deck
rewinds to the beginning of the ID, then "ID
ERASE" appears as the deck erases the ID.
In the case of a skip ID, if the SKIP ID indicator has
been turned off by the time you press ERASE, the
deck will still erase the skip ID.
To erase an end ID
Press ERASE.
"(ERASE)" appears in the display while the deck
fast-forwards to the beginning of the end ID, then
"ID ERASE" appears while the deck erases the end
ID.
• It takes 9 seconds to erase a start ID.
• It takes 1 second to erase a skip ID.
• It takes 9 seconds to erase an end ID.
• Program numbers are erased together with start
IDs.
z
You can erase an ID even when it is not displayed
Just press the ERASE button. The tape is rewound, and
the first ID detected is erased.
z
You can use the End Search function to locate the
end ID
See page 10.
Note
A skip ID written at the same position of a start ID is erased
when the start ID is erased.
18
EN
MARGIN
ID
RESET
AUTO
RENUMBER
g
WRITE
FF
MODE
RESET
)
MENU
ENTER
ID MODE
REC MODE
STANDARD
PAUSE
REC MUTING
REC
START
48 kHz
OPEN/CLOSE
STOP
44.1kHz
P
R
r
6
END
LONG
ID MODE
ERASE
Renumbering the Program
Numbers Automatically
REC LEVEL
(Renumbering)
5
REHEARSAL
4
6
3
7
2
8
ERASE
1
9
0
10
CH-1 (L)
CH-2 (R)
SBM
PHONES
PHONE LEVEL
Renumbering searches for each start ID from the
ON
OFF
MIN
MAX
beginning of the tape and assigns a new program
number to each one starting with 1. Use Renumbering
function in the following cases:
• When you've added a start ID while playing the tape
• When a program number is missing due to an erased
start ID
• When you began recording from the middle of the
tape and wrote a program number that already
exists, or when one of the the start IDs has no
program number.
INPUT
ANALOG OPT
COAXIAL
POWER
Press ID RENUMBER while the deck is stopped or
playing.
The RENUMBER indicator flashes in the display and
the tape is automatically rewound to its beginning.
The deck then starts searching for each successive start
ID writing a new program number for each one
starting with 1. The RENUMBER indicator stops
flashing and "ID WRITE" appears in the display for a
few seconds as the deck begins rewriting the program
numbers.
After renumbering is finished, the deck rewinds the
tape automatically to its beginning, then stops.
z
You can specify the first program number to be
assigned to the first track
For details, see "Menu Operations" ("FIRST(PGM
NO.)") on page 20.
Note
Renumbering function may not function correctly when:
• A blank section exists on the tape.
• The interval between two start IDs is less than 18 seconds
(36 seconds in long-play mode).
• A start ID exists within 10 seconds from the end of the
tape.
MARGIN
RESET
g
AMS
REW
FF
MODE
RESET
=
+
0
)
SELECT
DATA
MENU
ENTER
STOP
PLAY
PAUSE
REC MUTING
REC
OPEN/CLOSE
p
"
P
R
r
ID RENUMBER
REC LEVEL
ID
5
4
6
AUTO
RENUMBER
REHEARSAL
3
7
2
8
WRITE
ERASE
1
9
0
10
CH-1 (L)
CH-2 (R)
ID MODE
REC MODE
SBM
PHONES
PHONE LEVEL
STANDARD
START
48 kHz
ON
STOP
44.1kHz
6
OFF
END
LONG
MIN
MAX
Werbung
Kapitel
Inhaltsverzeichnis
