Seite 1
DELTA Schiebetüren Montageanleitung Sliding doors Assembly Instructions...
Seite 2
DELTA Kommissionszeichnung Inhalt Echtholzfurniere mit einem leicht feuchten, Zu jeder Kommission wird eine Zeichnung lederartigen Tuch abwischen und anschließend erstellt, aus der sich die Anordnung der Teile trockenreiben. Keine nassen Tücher verwenden! Systemkomponenten 2 entnehmen lässt. Spezielle Artikel werden Sandhaltige oder schmirgelnde Scheuermittel Vorbemerkungen 3 durch eine Detailzeichnung erläutert.
Pro l- und Türserien Deckenschiene Ceiling track Diese Montageanleitung gilt für alle Pro l- und Türserien der DELTA Schiebetüren. Die einzelnen Arbeitsschritte werden in der Montageanlei- tung immer anhand der Pro lserie PUR dargestellt. Die gelieferten Schiebetüren können also von den Darstellungen in der Montageanleitung abweichen.
Seite 4
For doors in the DUO pro le series, the oor track must be mounted with a 6–7 mm o set towards the back! For doors in the SLIM-LINE pro le series, the oor track must be mounted with a 12 mm o set towards the back! AN Collection GmbH T. +49 (0) 5205 7502-14...
Seite 5
6–7 mm o set towards the back! For doors in the SLIM-LINE pro le series, the oor track must be mounted with a 12 potentially cause damage to the ooring. mm o set towards the back! AN Collection GmbH T. +49 (0) 5205 7502-14...
Seite 6
If necessary, glue brush seals to the backs of the vertical pro les in the overlapping areas. 5. Adjust the dampers in the upper roller block using the Allen key bolt. AN Collection GmbH T. +49 (0) 5205 7502-14...
Seite 7
7. Remove the adhesive strip and stick the doubling pro le onto the rear edge of the vertical pro le. Stick the brush seal onto the doubling pro le. AN Collection GmbH T. +49 (0) 5205 7502-14...
Seite 8
5. At the moment when the catch pin slot moves onto the catch pin, the distance between the door frame and the wall or end of the rail is approximately 135 mm. AN Collection GmbH T. +49 (0) 5205 7502-14...
Seite 9
Use screw clamps to tighten the panel for a few hours. 3. The panel is held in place by the adhesive tape strip after removing the screw clamps. The silicone is only fully adherent after approxi- mately 24 hours. AN Collection GmbH T. +49 (0) 5205 7502-14...
Seite 10
6. Attach the brush seals to the compensation pro les rather than to the vertical pro les of the sliding doors. They serve as both a bu er seal and a cover for the drill holes in the compensation pro les. AN Collection GmbH T. +49 (0) 5205 7502-14...
Seite 11
Use screw clamps to tighten the panels for a few hours. The panels are held in place by the adhesive tape strip after removing the screw clamps. The silicone is only fully adherent after approximately 24 hours. AN Collection GmbH T. +49 (0) 5205 7502-14...
Seite 12
Then clip on the cover pro le. 3. Position the stopper and screw it into the guide track from below with the corres- ponding screw. Place the cover caps on the side of the guide track. AN Collection GmbH T. +49 (0) 5205 7502-14...
Seite 13
Now insert the sliding doors – see page 7 onwards for details on mounting grooves in the ceiling track. If stopper brackets are used, the screw and alignment. channel covers can only be clipped in once the stopper brackets have been aligned. AN Collection GmbH T. +49 (0) 5205 7502-14...
Seite 14
The frame pro les must be clean and free of oil and grease before the corner pro les, rubber seals and punched hole covers are glued on. 3. Mount the position springs and end stoppers as described above. AN Collection GmbH T. +49 (0) 5205 7502-14...
Seite 15
3. Screw the lock plate to the oor track so that the oor lock bolt ts exactly into the recess. AN Collection GmbH T. +49 (0) 5205 7502-14...
Seite 17
DELTA Montageanleitung Stand Dezember 2021 AN Collection GmbH Heidegrundweg 104 – 108 33689 Bielefeld T. +49 (0) 5205 7502-14 F. +49 (0) 5205 7502-43 mail@an-collection.com www.an-collection.com...