Bender ISOMETER isoRW425 Kurzanleitung Seite 10

ISOMETER® isoRW425
Anschluss
Anschlussart ............................................... Schraub- oder Federklemme
Schraubklemmen:
Nennstrom ................................................................................... ≤ 10 A
Anzugsmoment ............................................0,5...0,6 Nm (5...7 lb-in)
Leitergrößen .........................................................................AWG 24-12
Abisolierlänge ................................................................................8 mm
Starr/flexibel ....................................................................0,2...2,5 mm²
Flexibel mit Aderendhülse mit/ohne Kunststoffhülse .............................
.......................................................................................0,25...2,5 mm²
Mehrleiter starr ................................................................0,2...1,5 mm²
Mehrleiter flexibel ...........................................................0,2...1,5 mm²
Mehrleiter flexibel mit Aderendhülse ohne Kunststoffhülse ...................
.......................................................................................0,25...1,5 mm²
Mehrleiter flexibel mit TWIN Aderendhülse ohne Kunststoffhülse .........
.......................................................................................0,25...1,5 mm²
Federklemmen:
Nennstrom ................................................................................... ≤ 10 A
Leitergrößen .........................................................................AWG 24-14
Abisolierlänge ..............................................................................10 mm
Starr .................................................................................0,2...2,5 mm²
Flexibel ohne Aderendhülse ...........................................0,75...2,5 mm²
Flexibel mit Aderendhülse mit/ohne Kunststoffhülse .............................
.......................................................................................0,25...2,5 mm²
Mehrleiter flexibel mit TWIN Aderendhülse mit Kunststoffhülse ............
.........................................................................................0,5...1,5 mm²
Öffnungskraft ...................................................................................50 N
Testöffnung, Durchmesser ..........................................................2,1 mm
Sonstiges
Betriebsart ......................................................................... Dauerbetrieb
Einbaulage .............. Kühlschlitze müssen senkrecht durchlüftet werden
Entflammbarkeitsklasse ............................................................UL 94V-0
Schutzart Einbauten (DIN EN 60529) ............................................... IP30
Schutzart Klemmen (DIN EN 60529) ................................................ IP20
10 isoRW425_D00052_06_Q_DEEN / 11.2023
Connection
Connection type .................................screw-type or push-wire terminal
Screw-type terminals:
Nominal current ........................................................................... ≤ 10 A
Tightening torque .........................................0.5...0.6 Nm (5...7 lb-in)
Conductor sizes .....................................................................AWG 24-12
Stripping length .............................................................................8 mm
Rigid/flexible ...................................................................0.2...2.5 mm²
Flexible with ferrules with/without plastic sleeve ..................................
.......................................................................................0.25...2.5 mm²
Multi-conductor rigid .......................................................0.2...1.5 mm²
Multi-conductor flexible ..................................................0.2...1.5 mm²
Multi-conductor flexible with ferrules without plastic sleeve .................
.......................................................................................0.25...1.5 mm²
Multi-conductor flexible with TWIN ferrules with plastic sleeve .............
.......................................................................................0.25...1.5 mm²
Push-wire terminals:
Nominal current ........................................................................... ≤ 10 A
Conductor sizes .....................................................................AWG 24-14
Stripping length ...........................................................................10 mm
Rigid ................................................................................0.2...2.5 mm²
Flexible without ferrules ................................................0.75...2.5 mm²
Flexible with ferrules with/without plastic sleeve ..................................
.......................................................................................0.25...2.5 mm²
Multi-conductor flexible with TWIN ferrules with plastic sleeve .............
.........................................................................................0.5...1.5 mm²
Opening force ..................................................................................50 N
Test opening, diameter ...............................................................2.1 mm
Other
Operating mode ...................................................... continous operation
Mounting .............................. cooling slots must be ventilated vertically
Flammability class ....................................................................UL 94V-0
Degree of protection, built-in components (DIN EN 60529) ............. IP30
Degree of protection, terminals (DIN EN 60529) .............................. IP20