Measuring Range; Can-Schnittstelle; Can Interface - Bender ISOMETER iso175 Kurzanleitung

Messbereich
R_iso_corrected ....................................................................0...35 MΩ
R_iso_original .......................................................................0...50 MΩ
Messbereich
Isolation: R_iso_neg* ...........................................................0...50 MΩ
Isolation: R_iso_pos* ............................................................0...50 MΩ
Voltage: HV-System Spannungsmessung .............................0...1000 V
Toleranz Voltage: HV-System Spannungsmessung ..............±5 % ± 2 V
Voltage: HV_pos_to_Earth ..................................................0...1000 V
Toleranz Voltage: HV_pos_to_Earth...................................±5 % ± 2 V
Voltage: HV_neg_to_Earth .................................................0...1000 V
Toleranz Voltage: HV_neg_to_Earth ..................................±5 % ± 2 V
Capacity C : Measured_Value ................................................ 0...10 μF
e
Toleranz Capacity C : Measured_Value ..............................................tbd
e
Unbalance ..............................................................................0...100 %
Toleranz Unbalance ...........................................................................tbd
Relative Messunsicherheit der geschätzten Messwerte bei Schnellstart-
messung: R_iso_status = 0xFC ........................................... 0...-100 %
* verfügbar ab HV-Spannung > 100 V
Toleranz „R_iso_corrected" (R_iso_status = 0xFD) ..............................
Messbereich ............................................................... Abs. Fehler
0kΩ...-50 kΩ ........................................................... 0kΩ...-50 kΩ
Messbereich ................................................................Rel. Fehler
50 kΩ...1,2 MΩ ................................... 0...-120 % bis 0...-48 %
1,2 MΩ...5 MΩ ...................................... 0...-48 % bis 0...-76 %
5 MΩ...10 MΩ .............................................................. 0...-76 %
> 10 MΩ ................................................................. keine Angaben
Toleranz „R_iso_corrected" (R_iso_status = 0xFE) ...............................
Messbereich ............................................................... Abs. Fehler
0kΩ...-50 kΩ ........................................................... 0kΩ...-50 kΩ
Messbereich ................................................................Rel. Fehler
50 kΩ...1,2 MΩ ..................................... 0...-60 % bis 0...-24 %
1,2 MΩ...5 MΩ ...................................... 0...-24 % bis 0...-38 %
5 MΩ...10 MΩ .............................................................. 0...-38 %
> 10 MΩ ................................................................. keine Angaben

CAN-Schnittstelle

Datenübertragungsrate ................ 125, 250, 500, 666, 800, 1000 kBaud
Terminierungswiderstand ............................................................120 Ω*
* über Jumper: Empfohlen: Weitronictw Jumper series 165.
Herst.Best.Nr.: 165-101-10-10

Measuring range

R_iso_corrected ....................................................................0...35 MΩ
R_iso_original .......................................................................0...50 MΩ
Measuring range
Isolation: R_iso_neg* ...........................................................0...50 MΩ
Isolation: R_iso_pos* ............................................................0...50 MΩ
Voltage: HV system voltage measurement ..........................0...1000 V
Tolerance Voltage: HV system voltage measurement .........±5 % ± 2 V
Voltage: HV_pos_to_Earth ..................................................0...1000 V
Tolerance Voltage: HV_pos_to_Earth .................................±5 % ± 2 V
Voltage: HV_neg_to_Earth .................................................0...1000 V
Tolerance Voltage: HV_neg_to_Earth ................................±5 % ± 2 V
Capacity C : Measured_Value ................................................ 0...10 μF
e
Toleranz Capacity C : Measured_Value ..............................................tbd
e
Unbalance ..............................................................................0...100 %
Tolerance Unbalance ..........................................................................tbd
Relative uncertainty of the estimated measured values of the fast start
measurement: R_iso_status = 0xFC) .................................. 0...-100 %
* Available from an HV voltage > 100 V
Tolerance „R_iso_corrected" (R_iso_status = 0xFD) ............................
Measuring range ..........................................................Abs. fault
0kΩ...-50 kΩ ........................................................... 0kΩ...-50 kΩ
Measuring range ...........................................................Rel. fault
50 kΩ...1,2 MΩ ................................... 0...-120 % bis 0...-48 %
1,2 MΩ...5 MΩ ...................................... 0...-48 % bis 0...-76 %
5 MΩ...10 MΩ .............................................................. 0...-76 %
> 10 MΩ .....................................................................not specified
Toleranz „R_iso_corrected" (R_iso_status = 0xFE) ...............................
Measuring range ..........................................................Abs. fault
0kΩ...-50 kΩ ........................................................... 0kΩ...-50 kΩ
Measuring range ...........................................................Rel. fault
50 kΩ...1,2 MΩ ..................................... 0...-60 % bis 0...-24 %
1,2 MΩ...5 MΩ ...................................... 0...-24 % bis 0...-38 %
5 MΩ...10 MΩ .............................................................. 0...-38 %
> 10 MΩ .....................................................................not specified

CAN interface

Data transmission rate .................. 125, 250, 500, 666, 800, 1000 kBaud
Terminating resistor.....................................................................120 Ω*
* via jumper: Recommended: Weitronictw Jumper series 165.
Manufacturer ordering no.: 165-101-10-10
iso175_D00415_01_Q_DEEN/11.2023
ISOMETER® iso175
9