pizzato NG Serie Montageanleitung Seite 12

DC:
Mission time:
Ambient temperature:
Storage temperature:
Max. operating altitude:
Start time on switching on:
Max. actuation frequency
with actuator lock and release:
Mechanical endurance:
Max. actuation speed:
Min. actuation speed:
Mounting position:
Maximum force before breakage F
1max
Max. holding force F :
Zh
Maximum clearance of locked actuator:
Released actuator extraction force:
8.3 Power supply electrical data
Rated operating voltage U :
e
Operating current at U voltage:
e
- minimum:
- with activated solenoid:
- with activated solenoid and all outputs at maximum power: 1.2 A
Rated insulation voltage U :
i
Rated impulse withstand voltage U
imp
External protection fuse:
Overvoltage category:
Solenoid duty cycle:
Solenoid consumption:
Pollution degree:
8.3.1 Electrical data of IS1/IS2/I3/I4/I5/IE1/IE2/EDM inputs
Rated operating voltage U :
e1
Rated current consumption I :
e1
8.3.2 Electrical data of OS1/OS2 safety outputs
Rated operating voltage U :
e2
Output type:
Maximum current per output I :
e2
Minimum current per output I :
m2
Thermal current I :
th2
Utilization category:
Short circuit detection:
Overcurrent protection:
Internal self-resettable protection fuse:
Duration of the deactivation impulses at the safety outputs: < 300 µs
Maximum permissible capacitance between outputs: < 200 nF
Maximum permissible capacitance between output and ground: < 200 nF
Activation time of safety outputs OS1 and OS2 after deactivation of inputs:
Activation time after unlocking the door:
Maximum EDM signal status change delay: 500 ms
8.3.3 Electrical data of signalling outputs O3/O4
Rated operating voltage U :
e3
Output type:
Maximum current per output I :
e3
Utilization category:
Short circuit detection:
Overvoltage protection
Internal self-resettable protection fuse:
8.3.4 RFID sensor data
Assured operating distance S :
ao
Assured release distance S :
ar
Mode 1:
Modes 2 and 3:
Rated operating distance S :
n
Repeat accuracy:
Differential travel:
RFID transponder frequency:
Max. switching frequency:
Response time of safety outputs to actuator extraction:
Minimum distance between two identical devices to avoid reciprocal radio interferences:
8.4 Technical data of the integrated control devices
8.4.1 General data
Protection degree:
Mechanical endurance:
Spring-return button:
Emergency stop button:
Selector switch:
Key selector switch:
8.4.2 Actuating force
Spring-return button:
Emergency stop button:
Selector switch:
Key selector switch:
8.4.3 Contact block
Material of the contacts:
Contact type:
8.4.4 Electrical data
Thermal current (Ith):
Rated insulation voltage (Ui):
Rated impulse withstand voltage (Uimp):
LED supply voltage:
LED supply current:
high
20 years
-20°C ... +50°C
-40°C ... +75°C
2000 m
2 s
600 operating cycles/hour
1 million operating cycles
0.5 m/s
1 mm/s
any
: 9750 N acc. to EN ISO 14119
7500 N acc. to EN ISO 14119
4 mm
~ 30 N
24 Vdc ±10% SELV/PELV
40 mA
0.4 A
32 Vdc
: 1.5 kV
2 A type gG or equivalent device
III
100% ED
9 W
3 acc. to EN 60947-1
24 Vdc
5 mA
24 Vdc
PNP type OSSD
0.25 A
0.5 mA
0.25 A
DC13; U =24 Vdc, I =0.25 A
e2 e2
Yes
Yes
1.1 A
Typically 7 ms, max. 15 ms
Typically 7 ms, max. 12 ms
24 Vdc
PNP
0.1 A
DC13; U =24 Vdc, I =0.1 A
e3 e3
No
Yes
1.1 A
2 mm
4 mm (actuator not locked)
10 mm (actuator locked)
10 mm (actuator locked and not locked)
2.5 mm
≤10 % s
n
≤20 % s
n
125 khz
1 hz
typically 120 ms, max. 200 ms
2 mm
IP65 acc. to EN 60529
1 million operating cycles
50,000 operating cycles
300,000 operating cycles
50,000 operating cycles
30,000 operating cycles including removal of the key
4 N min 100 N max.
20 N min 100 N max.
0.1 Nm min 1.5 Nm max.
0.1 Nm min 1.3 Nm max.
silver contacts
Self-cleaning contacts with double interruption
1 A
32 Vac/dc
1.5 kV
24 Vdc ± 15%
10 mA per LED
8.4.5 Utilization category of the contact block
Direct current: DC-13
8.5 Compliance with standards
EN ISO 14119, EN 60947-5-3:2013, EN 60947-1, EN 60204-1, EN ISO 12100,
EN 60529, EN 61000-6-2, EN 61000-6-3, BG-GS-ET-19, IEC 61508:2010, SN 29500,
EN ISO 13849-1:2015, EN ISO 13849-2:2012, EN 62061:2005 + EC:2010 + A1:2013
+ A2:2015, EN 61326-1, EN 61326-3-1, EN 61326-3-2, ETSI 301 489-1, ETSI 301
489-3, ETSI 300 330-2, UL 508, CSA 22.2 No.14
IEC 60947-5-1, IEC 60947-5-5, EN ISO 13850
8.6 Compliance with directives
Machinery Directive 2006/42/EC, EMC Directive 2014/30/EU, Radio Equipment Di-
rective 2014/53/EU, RohS Directive 2011/65/EU
FCC Part 15 Statements:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired
operation.
9 SPECIAL VERSIONS ON REQUEST
Special versions of the device are available on request.
The special versions may differ substantially from the indications in this instruction
sheet.
The installer must ensure that he has received written information from the support
service regarding installation and use of the special version requested.
10 DISPOSAL
At the end of service life product must be disposed of properly, according to the
rules in force in the country in which the disposal takes place.
11 SUPPORT
The device can be used for safeguarding people's physical safety, therefore in case of
any doubt concerning installation or operation methods, always contact our technical
support service:
Pizzato Elettrica Srl
Via Torino, 1 - 36063 Marostica (VI) - ITALY
Telephone +39.0424.470.930
E-mail tech@pizzato.com
www.pizzato.com
Our support service provides assistance in Italian and English.
12 EC CONFORMITY DECLARATION
I, the undersigned, as a representative of the following manufacturer:
Pizzato Elettrica Srl - Via Torino, 1 - 36063 Marostica (VI) – ITALY
hereby declare that the product is in conformity with whatever prescribed by the 2006/42/
EC Machine Directive. The complete version of the present conformity declaration is
available on our website www.pizzato.com
Marco Pizzato
DISCLAIMER:
Subject to modifications without prior notice and errors excepted. The data given in this sheet are accurately
checked and refer to typical mass production values. The device descriptions and its applications, the
fields of application, the external control details, as well as information on installation and operation, are
provided to the best of our knowledge. This does not in any way mean that the characteristics described
may entail legal liabilities extending beyond the "General Terms of Sale", as stated in the Pizzato Elettrica
general catalogue. Customers/users are not absolved from the obligation to read and understand our
information and recommendations and pertinent technical standards, before using the products for their
own purposes. Taking into account the great variety of applications and possible connections of the device,
the examples and diagrams given in the present manual are to be considered as merely descriptive; the
user is deemed responsible for checking that the specific application of the device complies with current
standards. This document is a translation of the original instructions. In case of discrepancy between
the present sheet and the original copy, the Italian version shall prevail. All rights to the contents of this
publication are reserved in accordance with current legislation on the protection of intellectual property. The
reproduction, publication, distribution and modification, total or partial, of all or part of the original material
contained therein (including, but not limited to, texts, images, graphics), whether on paper or in electronic
form, are expressly prohibited without written permission from Pizzato Elettrica Srl.
All rights reserved. © 2021 Copyright Pizzato Elettrica
12/30
Ue = 24 V Ie = 0.55 A