Werbung
Verfügbare Sprachen
Verfügbare Sprachen
The WARRANTY does not cover fuel system damage or engine
performance problems resulting from neglected storage preparation.
ENGINE OIL
Change the engine oil (page 12).
ENGINE CYLINDER
If the mower is to be stored for more
than 3 months, remove the spark plug
(page 13). Pour 5 ~ 10 cc of clean
engine oil into the cylinder [1]. Pull the
starter rope several times to distribute
the oil in the cylinder. Reinstall the
spark plug.
Pull the starter rope slowly until
resistance is felt, then return the starter grip gently. This will close the
valves so moisture cannot enter the engine cylinder.
PLACING IN STORAGE
Since your mower will be stored with petrol in the fuel tank and
carburetor, it is important to reduce the hazard of petrol vapor ignition.
Select a well-ventilated storage area away from any appliance that
operates with a flame, such as a furnace, water heater, or clothes
dryer. Also avoid any area with a spark-producing electric motor, or
where power tools are operated.
If possible, avoid storage areas with high humidity, because that
promotes rust and corrosion.
Place the mower with its wheels on a level surface. Tilting can cause
fuel or oil leakage. The handlebar can be folded for compact storage,
shown below.
With the engine and exhaust system cool, cover the mower to keep
out dust. A hot engine and exhaust system can ignite or melt some
materials. Do not use sheet plastic as a dust cover. A nonporous
cover will trap moisture around the mower, promoting rust and
corrosion.
Handlebar Folding
1. Remove the grass catcher. You can place it on top of the engine,
with the catcher opening to the front.
2. Support and hold the handlebar.
3. Unlock the handlebar adjust knobs
2
forward
into the storage position.
NOTICE
Do not allow the control cables
kinked while folding the handlebar down into the storage position.
The cables or engine control system may be damaged causing the
lawnmower to not function properly.
REMOVING FROM STORAGE
Check your mower as described in PRE-OPERATION CHECKS
(page 6).
16
[1]
OIL
1
and fold the handlebar
to become caught, pinched, or
3
If the cylinder was coated with oil during storage preparation, the
engine will smoke briefly at startup. This is normal.
FRAME AND ENGINE SERIAL NUMBER
Record the frame and engine serial numbers (page 3) in the space
below. You will need these numbers when ordering parts and when
making technical or warranty inquires.
Frame serial number:___________________________
Engine serial number:___________________________
Date of purchase:______/______/______
PARTS
Item
Air Cleaner
Spark Plug
Cutting Means:
Lower
Upper
Cutting-means Bolt (2)
Bolt Washer (2)
Wheel/tire
TROUBLESHOOTING
ENGINE WILL NOT START
Possible Cause
Fuel valve OFF
Out of fuel
Throttle in wrong position
(VYEA only)
Bad fuel; mower stored without
treating the petrol, or refueled
with bad petrol
Spark plug faulty, fouled, or
improperly gapped
Spark plug wet with fuel (flooded
engine)
Fuel filter clogged, carburetor
malfunction, ignition malfunction,
valves stuck, etc.
LOSS OF POWER
Possible Cause
Grass is too tall to cut
Throttle not set to FAST
(VYEA only)
Cutting-means enclosure is
clogged
Air cleaner is clogged
Bad fuel; mower stored without
treating the petrol, or refueled
with bad petrol
Fuel filter clogged, carburetor
malfunction, ignition malfunction,
valves stuck, etc.
ENGLISH
Part Number
17211-Z8B-901
98079-55846
NGK (brand) BPR5ES
Always use an upper and
72511-VR8-M00
lower cutting means as a set.
72531-VR8-M00
90105-960-710
2 required, 10 x 20 mm
90502-VG3-000
2 required
44710-VR8-N00
42710-VR8-N00
Correction
Turn the fuel valve ON (page 5).
Refuel (page 7).
Move throttle lever to FAST position
(page 5).
Refuel with fresh petrol (page 7).
Gap or replace the spark plug
(page 13).
Dry and reinstall the spark plug.
Take the mower to an authorized
Honda servicing dealer or refer to the
shop manual for repair.
Correction
Raise the cutting height (page 8), cut a
narrower swath, use a slower ground
speed, or cut more frequently.
Move the throttle lever to FAST
(page 5).
Clean out the cutting-means enclosure
(page 11).
Clean or replace the air cleaner
Refuel with fresh petrol (page 7).
Take the mower to an authorized
Honda servicing dealer or refer to the
shop manual for repair.
Notes
Paper
Front
Rear
Werbung
