Werbung
Verfügbare Sprachen
Verfügbare Sprachen
HOW TO USE MANUAL SERVICE MODE
(8) Number of times of cancellation by track skips data
Format: 8RCR
Number of times of cancellation by track skips data includes data
for a maximum
of 54 discs. The data for a disc is transmitted
each time this command is input (transmission sequence is most
often
cancelled
disc
through
least
often
cancelled
disc).
Therefore, the command
must be input a maximum of 54 times
to obtain the data for 54 discs (until ":" (3Ah) is transmitted with
the data). However,
only the number of discs actually cancelled
by track skip is transmitted.
The disc number is indicated by the first two digits from the left.
The number of times the disc was cancelled is indicated by the
following digits. The number of times the disc was cancelled has
a maximum
of three digits, and can range from O through 255.
Therefore,
the data
for a disc consists of a minimum
of three
digits, and a maximum of five digits.
Example:
8RCR
1110CR
No. 1
8RCR
218CR
No. 2
|
|
|
|
|
8RCR
432:CR
No. 5
There were five discs cancelled in this example, and the disc
most often cancelled was disc no. 11, which was cancelled ten
times. The fifth most cancelled disc was disc no. 43, which was
cancelled twice.
(9) ID No.
Format: 9RCR
The 11-digit ID No. is transmitted.
Example:
9RCR
12345678912:CR
The currently registered ID No. is 12345678912.
(10) ROM version
Format: 10RCR
The software version stored in ROM is transmitted as a 2-digit
number.
Example:
10RCR
11:CR
The version loaded in ROM is 1.1.
(11) Coin weight settings
Format:
11RCR
The settings for five types of coins are transmitted as a 10-digit
number.
Each
2-digits,
beginning
from
the
left, denote
the
weighting of a coin (transmission sequence is coin B, followed by
coin C, coin D, coin E, and coin F).
Example:
11RCR
0102030405:CR
32
<DRB1045>
En
Coin Bis set to 1, coin C to 2, coin D to 3, coin E to 4, and coin F
to 5 in this example.
(12) Credit rates
Format:
12RCR
The credit rate settings for 20 levels are transmitted as a 40-digit
number. Each 2-digits, beginning from the left, denote the rate
level setting for that unit (transmission sequence is lowest level
to highest level).
Example:
12RCR
01000000050000000010
000000001 50000000020
:CR
The rates are set to issue credits (unit 1 for one credit, unit 5 for
five credits, unit 10 for ten credits, unit 15 for
15 credits, and unit
20 for 20 credits).
(13) Number of times of cancellation by track skips
Format:
13RCR
The setting for the number of times of cancellation by track skips
are transmitted as a 2-digit number.
Example:
13RCR
10:CR
The
number
of times
of cancellation
by track
skips
until
cancellation results is set at 10 in this example.
(14) Auto-play interval time
Format: 14RCR
The setting for auto-play interval time is transmitted as a 2-digit
number.
Example:
14RCR
10:CR
The auto-play interval time is set at 10 minutes in this example.
(15) DIP switches
Format: 15RCR
The DIP switch settings are transmitted (transmission sequence
is DIP switch no. 1 through no. 8). Zero ("0") indicates that the
switch is OFF, while "1" indicates that the switch is ON.
Example:
15RCR
01100100:CR
The
DIP switch
settings
in this example
are
paid
playback,
random auto-play, TOC initialize OFF when power is ON, and a
transmission speed of 4800 bps for RS-232C data output.
Werbung
