EINHELL GC-LB 18 Li Originalbetriebsanleitung Seite 14

be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
equipment is used in commercial, trade or indust-
rial businesses or for equivalent purposes.
4. Technical data
Idle speed n ....................................13,000 min
0
Air speed ...............................................210 km/h
Max. operating time ..................... approx. 14 min
Protection class: ................................................III
Weight: .......................................................1.6 kg
Caution!
The equipment is supplied without batteries and
without a charger and is allowed to be used only
with the lithium-ion batteries of the Power-X-
Change series!
The lithium-ion batteries of the Power-X-Change
series are allowed to be charged only with the
Power-X charger.
Danger!
Noise and vibration
Sound and vibration values were measured in
accordance with ISO 22868.
Sound pressure level L
Uncertainty K ............................................. 3 dB
pA
Measured sound power level L
Uncertainty K ............................................ 3 dB
WA
Guaranteed sound power level L
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with ISO 22867.
Handle under load
Vibration emission value a
Uncertainty K = 2.0 m/s
Anl_GC_LB_18_Li_SPK7.indb 14 Anl_GC_LB_18_Li_SPK7.indb 14
-1
....................... 73 dB(A)
pA
......... 90 dB(A)
WA
........ 93 dB(A)
WA
= 4.0 m/s
2
h
2
- 14 -
GB
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The quoted vibration value can be used to com-
pare the equipment with another electric power
tool.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
5. Before starting the equipment
5.1 Fitting the blower tube (Fig. 3-5)
Plug together the motor unit (Fig. 3/Item 3) and
the blower tube (Fig. 3/Item 1). Then screw the
two parts together as shown in Fig. 5 using the
fastening screw (Fig. 5/Item 6).
5.2 Fitting the battery pack (Fig. 6/7)
Press the pushlock button of the battery pack as
shown in Fig. 6 and push the battery pack into the
mount provided. When the battery pack is posi-
tioned as in Fig. 7, make sure that the pushlock
button latches in place! To remove the battery
pack, proceed in reverse order.
5.3 Charging the battery (Fig. 7)
1. Take the battery pack out of the equipment.
Do this by pressing the side pushlock buttons.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(4) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Insert the battery pack (5) into the battery
charger (4).
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
14.06.2023 14:44:23 14.06.2023 14:44:23