Panasonic WJ-AVE3 Bedienungsanleitung Seite 8

39.
40,
41.
42.
43.
44,
45,
Scroll Speed Control (SPEED)
This control adjusts the scrolling speed from 0.6
seconds to 8.1 seconds.
Superimpose Effect ON/OFF Button
(SUPERIMPOSE EFFECT)
This is the Superimpose Effect on/off button. Only
when this button is lit, the overall superimpose effects
become available.
Memory Page 1 Button (PAGE 1)
This button has 2 functions. One is to memorize the
superimposed image into the memory page 14, the other
one is to recall the image from it.
Memory Page 2 Button (PAGE 2)
This button has 2 functions. One is to memorize the
superimposed image into the memory page 2, the other
one is to recall the image from it.
Store Button (STORE)
It is nessary to press this button to enter an image
into memory. This button should be pressed before .
the Memory Page 1 Button (41) or the Memory Page 2
Button (42).
Display Button (DISPLAY)
The superimpose video signal supplied to the
Superimpose Input Connector/Jack on the rear panel
will be displayed on the screen by pressing this button
(LED lights). The Superimpose Effect ON/OFF Button
(40) should be pressed at this time to perform the
Display function.
Superimpose Key Level Control (KEY LEVEL)
This control adjusts the key level of the superimpose
video signal.
Colour Correction
It is. necessary to. press the Colour Correction ON/OFF
Button (46) to perform the functions from item-46 to item-50.
46,
47.
48.
Colour Correction ON/OFF Button
(COLOUR CORRECTION)
This is the Colour Correction on/off button. Only when
this button is pressed (LED lights), the overall colour
correction becomes available.
Colour Saturation Control (SATURATION)
This control adjusts the colour level of the images of:
the Source Video Signal.
When this control is set to the MAX position, it
generates the equal colour level to the Source Video
Signal,
Mono Colour Selector (MONO)
When this button is pressed, the LED lights. The
Source Video Signal becomes a single colour. The
RGB Joystick is used to select the colour. Placing the
joystick in the center makes the video signal Black and
white.
49.
. 50.
Colour Hold Button (HOLD)
The colour selected by the RGB Joystick (50) can be
held by pressing this button (LED lights).
RGB Joystick (R/G/B)
This Joystick permits you to balance or change the tint
of the images of the Source Video Signal by moving
its position. When this Joystick is positioned at center,
it generates the original colour of the Source Video
Signal.
Inputs/Outputs
$1.
52,
§3.
54.
55.
56.
" '57.
58.
59.
Y/C Source Input Connector (SOURCE Y/C)
This source input connector is for use with S-VHS
products. Use a S-Video Cable (4 pin) to feed the
S-Video Signal to this connector.
Composite Video Source Input Connector
(SOURCE COMP.)
This source input connector is for use with standard
video connections. Use shielded video cable (75 ohms)
to feed the video signal to this connector,
Source Audio Input Jacks (SOURCE AUDIO IN)
A stereo audio signal can be used for these jacks.
When monaural audio is to be used, connect it to the
L-channel. The monaural audio output can be obtained
at both R-channel and L-channel Audio Output Jacks
(59).
Y/C Superimpose Input Connector
(SUPERIMPOSE Y/C)
This superimpose input connector is for a S-VHS type
camera. Use a S-Video Cable (4 pin) to feed the
S-Video Signal to this connector.
Camera Superimpose Input Connector
(SUPERIMPOSE COMP.)
This superimpose input connector is for a video signal
from a standard camera. Use a shielded cable (75
ohms) to feed the video signal to this connector.
Auxiliary Audio Input Jacks (AUX AUDIO IN)
A stereo audio signal can be used for these jacks.
When monaural audio is to be used, connect it to the
L-channel. The monaural audio output can be obtained
at both R-channel and L-channel Audio Output Jacks
(59).
Y/C Video Output Connector
(REC VIDEO OUT Y/C)
This is the recording output connector for the S-VHS
VTR. Use a S-Video Cable (4 pin) to supply the S-Video
Signal to the S-VHS VTR.
Composite Video Output Connector
(REC VIDEO OUT COMP.)
This is the recording output connector for the standard
VTR. Use a shielded video cable (75 ohms) to supply
the video signal to the VTR.
Audio Output Jacks (AUDIO OUT)
The stereo audio signal can be obtained at these
connectors for recording.