Werbung
Common Operating Procedures (cont'd)
ome
* *
S70 MEVEREE TO CHANGER CONTROL
Sound Memory
With this unit's Sound Memory features, you can store your favorite each audio level of volume/bass/treble/
balance,/fader in up to 6 memories on the preset buttons 1 through 6, allowing you to recall it from memory
in any mode of FM, AM, TAPE, CD changer and AUX,
' 1 To store audio levels in memory
| @ Adjust volume/bass/treble/balance/fader leveis by following the procedures on Page 4.
@ When desired selections have been made, press the SEL button to select the SOUND mode, and
hold one of the nee buttons for more than 2 seconds to store them in memory.
i
Display shows "SJuUN3"and the selected button number.
2 To recall audio levels trom memory
i
Press the SEL button to select the SOUND mode, and press one of the preset buttons to recall the
|
audio level from memory in each mode of FM, AM, TAPE, CD changer and AUX.
!
Display shows "SJUNJ" for 2 seconds and the selected button number.
Notes:
®@ When the audio level is adjusted during the sound memory recalling, the display will change to the
audio adjusting mode.
@ The following shows the initial set values of each audio mode in this unit.
:
level
i
H
Volume
20
Bass
Center
Treble
Center
!
Balance
Center
:
i
Fader
Center
}
NS.
3 To check memorized audio levels
:
While the display shows © SQUN3
" by following step 2, press the SEL button repeatedly to recall the
f
\ memorized audio level in each audio mode.
When an audio control mode is selected but no operation is made within 5 seconds, the disptay will
.
return to the normal operation {volume adjustment) mode. in such a case. press the SEL button again
I
: to select the next control mode.
i
Radio Play Operations
1
Stereo Indicator
Radio Frequency indicator
y)
6 ' 7
Band Indicator
Mono indicator
Local Indicator
Preset Station Indicator
1 To change to the tuner mode
Press the "PWR" button on.
re
2 To select the desired band
Each time this button is pressed, the band will
change in the following sequence:
FM1
—
FM2
—
FM3 —
AM (LW.MW)
aes
os ee
! |nitial operation is preset for FM1 band.
3 Manual tuning
By pressing the ~ v TUNE" or "TUNE A" but-
ton, you can tune the frequency downward
or
upward.
4 Seek tuning
Press " v SEEK" or "SEEK "" button for more
than a half second, seek tuning will operate
and
stop
automatically
on
the
next
strong
Station.
Hold
the
button
depressed
to se-
quentially
advance
or
decrease
successive
available stations
untii you find the desired
_ one.
'
'
| 5 To tune in a preset station
Press the preset buttons to recall the previous
preset stations. (Please refer to the step 4 on
page 6 .)
6 To reduce interference during FM
stereo broadcasts (MONO Button)
Press the MONO-LOC button for more than 2
seconds to switch monaural reception in case
much interference is present in an FM stereo
signal or to improve the listening quality of
weak
FM broadcasts.
Press MONO-LOC
to
switch the mode in the following order.
| MONO OFF—--~ MONO OFF
MONO ON
MONO ON
OX MODE
LOC MODE
DX MODE
LOC MODE
4
i
'
| '
|
}
7
Switch from DX to LOC
|
i Normally,
searching
stops
even
at a weak
| wave station.
| To stop searching
at a strong wave
station
i only, press MONO.-LOC for more than 2 seconds.
During the AM band reception, press to switch
on or off the LOC mode as follows.
LOC OFF - LOC ON
N319/N210208-0
N231SZ0u-09
Werbung
