Werbung
Speaker Connections
with smal input ratings can cauee damage to the speakers.
cause damage to the speekers or this unit.
extension cord.
n this unit should be sble to handle more than 25W Of audio power. If an optionel
amplter weet, he spesiars shoudl bo abo to hafuie We mairurn oat power of fe erie. Use of Speakers
3. The-speaker impedance should be 4 - 8 ohms. ff the impedance is 100 jarge or 100 email, ft affects the output ana may
4. Do not use S-wire type apeeher system having a common earth ead. Never connect the speaker ord to the body af the
car. This unit uses the BTCL circuit, 80 each speaker should be connected separately using paralle! vinyl insulated cords.
5. The speaker cords and the power amplifier unit should be kept away (about 30cm gpert) from the antenna and.entenna _
6. Follow the connection diagram below carefully. Failure to do s0 may cause damage to both unit and speakers. :
@ Unit will be damaged if speakers (Front, Rear) are not connected property.
RIGHT
petted
2-SPEAKER SYSTEM
White
SPEAKER LEAD
|
LEFT
White w/black Stipe
|
FRONT
i
aa
Green
LEFT
Green w/Black Stripe
REAR
Cy
1
RIGHT
=
Gray w/Black Str
Stipe
FRONT
bites
4-SPEAKER SYSTEM
'a ae aaa an
Violet
REAR
—
roa
~~ eet w/Black Stripe
=
e
a
{=}
Dae
ae
nc
col
White
SPEAKER CORD
SPEAKER LEAD
ean
Lg
(+ 6 €)) 10 LEFT
LEFT
White w/Black Stripe
FONT:
+
$s
(-)
SPEAKER
LEFT
REAR
xia
Green w/Black
ck SBE
RIGHT
"gear //Black Sti
cee
Ww,
ipe
Pe
ale
RIGHT
Yow w/Black Stipe
SPEAKER CORD
Ne
(e508 eae
fro
SPEAKER
ee
(rer Bee
RIGHT
SPEAKER
{+ oF
Boe
ic or
ne
Installation
Preparation
© Before installation check the radio operation with antenna and speakers.
@ Disconnect the cable from the negative (—) battery terminal (see caution below).
Caution
For installation to cars with trip or navigational computers, all electronic memory settings previously registered in the
computer will be lost when the battery terminal is disconnected. For this type of cas, battery could not be discon-
nected. Therefore, extra care should be taken to prevent short circuiting.
in-dash Installation
instaltation Opening
in-dash installation can be done if the car's dashboard has an opening for this unit
ji
182 mm ——+}
as shown in Fig. 1. The car's dashboard should have a thickness of 4.5mm - 6mm
in order to make the installation of the unit.
Fig.
Installation Precautions
This equipment, if possibile, should be installed by a professional instalier.
This system is to be used only in a 12-volt, DC battery system (car) with negative ground.
(5mm:
1
2. Follow the electrical connection carefully. Failure to do so may result in damage to the unit.
3. Connect the power lead after other connections are made.
4. Be sure to connect the YELLOW lead to the positive terminal (+) of the battery of fuse block (BAT) terminal.
5. Insulate ali exposed wires to prevent short circuiting.
6. Secure all loose wires after installing the unit.
7. Please carefully ead the operating and installation instructions of the respective equipment before connecting it
to this unit.
Supplied Hardweres
| No. |
ttem
Diagram | Q'ty | | No.
item
rer
:
a
Soe A a hath
et
eke ac ei
zO) | Mounting Collar
@ | Toothed Lock Washer
|
1
@ | Plain Washer (5mm¢)
2
®
Monnibag Buk ad)
@ { Spring Washer (5mm¢}
2
® | Power Connector
@® | Hex. Nut (S5mm¢)
|
2
@
© | Rear Support Strap
1
1
© | Hex. Bolt (mm¢
x 25mm)
e
installation Procedures
1. Secure the Mounting Collar (.
insert Mounting Collar @ into the car's dashboard, and bend mounting tabs out with a screwdriver.
=
} : Dismounting Pin
® | Removable Face Plate
2. Secure the rear of the unit.
a) Check the electrical connection by referring to this operating instructions.
b) Connect the Mounting Bott ©, using a suitable wrench.
7
emai Bo
c) insert the unit into Mounting Collar ( and push it in until "click" is heard.
0) Secure the rear of the unit to the car by either of the two recommended methods on the next page.
Aa 1SZ04-09
N31D/N3
10204-0959
Werbung
