Scheppach HCP3000 Originalbetriebsanleitung Seite 35

12. Transport
m CAUTION
Risk of injury and damage!
• Note the weight of the device during transport.
12.1 Preparation for transport
Note:
Dispose of petrol in an environmentally friendly man-
ner!
1. Empty the fuel tank (9) with a fuel suction pump
(not included in the scope of delivery).
2. To ensure that no petrol remains in the carburet-
tor, the remaining petrol in the carburettor must be
drained out. To do this, place a suitable container
(not included in the scope of delivery) under the
carburettor and open the petrol drain screw (41).
Fig.16:
3. Drain the engine oil from the warm engine (as de-
scribed).
4. Remove the spark plug connector (31) from the
spark plug.
5. Wind up the high-pressure hose (2) and place it in
the hose holder (27).
6. Insert the spraying lance (17) into the transport
holder (4) and hang the hand spray gun (23) into
the transport holder (4).
7. Slide the device by the bow-type handle (1).
8. When transporting the device in vehicles, secure
it against rolling away, slipping and tipping, for ex-
ample with tension straps, in accordance with the
applicable directives.
13. Cleaning
m DANGER
Danger of injury due to unintentional start-up of the
device.
• Before working on the device, turn the engine
switch to "0/Off" and remove the spark plug con-
nector.
Danger of burning
• Do not touch hot silencers, cylinders or cooling fins.
m WARNING
• Switch off the device before carrying out any set-
ting or maintenance work.
• Remove the spark plug connector (31).
ATTENTION
• Switch off the device immediately and contact your
customer service:
- In the event of unusual vibrations or noises.
- If the engine seems overloaded or misfires.
• Keep protective devices, air vents and the engine
housing as free of dust and dirt as possible. Rub
the device clean with a dry cloth or blow it off with
compressed air at low pressure.
• We recommend that you clean the device directly
after every use.
• Clean the device at regular intervals using a damp
cloth and a little soft soap. Do not use chemical
cleaning agents or solvents. These could damage
the plastic parts of the device. Make sure that no
water penetrates the device interior.
13.1 Nozzle cleaning
If there is a pulsating sensation when the trigger
(24) is pressed, the nozzle (3) is potentially dirty or
clogged and should be cleaned immediately.
1. To clean the nozzle (3), switch off the engine and
stop the water supply.
2. Depressurise the device (see 11.6).
3. Remove the nozzle (3) from the spraying lance
(17). Make sure that the nozzle (3) points away
from you in a safe direction.
4. Use the nozzle cleaner needle (34) or a small pa-
per clip to remove debris from the nozzle (3).
5. Rinse the nozzle (3) with clear water.
6. Refit the nozzle (3) to the spraying lance (17).
7. Start the water supply and start the device.
13.2 Draining water
ATTENTION
Risk of damage!
• Freezing water in the device can destroy parts of
the device.
In winter, store the device preferably in a heated
room.
When storing in an unheated room, proceed as
follows:
1. Unscrew the water supply hose and high-pres-
sure hose (2).
2. Let the device run for max. 1 minute until the
pump and lines are empty.
14. Maintenance
m WARNING
• Switch off the device before carrying out any set-
ting or maintenance work.
• Remove the spark plug connector (31).
m DANGER
Danger of injury due to unintentional start-up of the
device.
• Before working on the device, turn the engine switch
to "0/Off" and remove the spark plug connector.
Danger of burning
• Do not touch hot silencers, cylinders or cooling fins.
www.scheppach.com
GB | 35