Scheppach HCP3000 Originalbetriebsanleitung Seite 32

9.5 Fitting the hand spray gun, spraying lance
(Fig. 6, 7, 8, 9)
m DANGER
• Danger of injury! The device, supply lines, high-pres-
sure hose and connections must be in perfect con-
dition. If their condition is not perfect, the device
must not be operated.
• Always tighten the fixing by hand! Too loose a con-
nection can lead to disconnection and cause injury.
1. Connect the spraying lance (17) to the hand spray
gun (23).
2. Hand-tighten the screwed connection of the
spraying lance (17).
3. Fit the high-pressure hose (2) to the hand spray
gun (23).
4. Attach the high-pressure hose (2) to the water
outlet (28) by turning the fixing.
10. Before commissioning
10.1 Filling/checking the engine oil (Fig.10)
ATTENTION
• The engine oil must be filled before the first use!
• Check the oil level before each start-up.
• Do not operate the device if no oil is visible on the
oil dipstick (12.1).
• Do not overfill the engine oil. Too high an oil level
can lead to engine damage.
• Refill the oil if necessary. Only use engine oil
(SAE10W30).
1. Place the device on a flat, even surface and re-
move any dirt from the area around the oil inlet/
dipstick (12)/oil tank cover with oil dipstick (12.1).
2. Open and remove the oil tank cover with oil dip-
stick (12.1) by turning anti-clockwise.
3. Fill the system with max. 400 ml four-stroke en-
gine oil (SAE10W30) as required.
4. Check the oil level using the marks on the oil dip-
stick.
5. Place on the oil tank cover with oil dipstick (12.1)
and close by turning clockwise.
10.2 Filling in fuel (Fig. 11)
m DANGER
Risk of fire and explosion!
• Use standard unleaded petrol with max. 10%
bioethanol component.
• Never refuel the device in enclosed spaces, with the
engine running or hot.
• Do not smoke when refuelling.
• Do not use a two-stroke mixture.
• Do not refuel near naked flames or sparks.
• Do not spill fuel. Use funnel.
• Wipe up spilled fuel.
• After refuelling, close the canister and tank properly.
32 | GB
1. Open and remove the fuel tank cover (8) by turn-
ing anti-clockwise.
2. Place a funnel (36) in the opening of the fuel tank (9).
3. Fill the fuel tank (9) with fuel up to max. 3-4 cm
below the top edge.
4. Replace the fuel tank cover (8) and close the fuel
tank (9) by turning clockwise.
10.3 Connecting the water supply (external) to
the pump (Fig. 12)
m WARNING
• If the inlet sieve is missing or damaged, do not
operate the high-pressure cleaner. Particles in the
high-pressure jet can cause injury.
ATTENTION
• The length of the free garden hose must be at least
3m between the inlet of the high-pressure cleaner
and a shut-off device, such as a Y shut-off coupling
or other suitable shut-off valve.
• Do not operate the high-pressure cleaner without a
water supply. If the high-pressure cleaner is operat-
ed without water, the high-pressure cleaner will be
damaged.
1. Before connecting the garden hose (NOT includ-
ed in the scope of delivery) to the water inlet (29),
check the inlet sieve. Clean a contaminated inlet
sieve, replace a damaged inlet sieve (40, Fig. 2).
2. To remove all impurities, run water through the
garden hose for 30 seconds. Shut off the water.
Important: Do not suction stagnant water for the
water supply. Only use water up to max. 40° C.
3. Fit the hose connection adapter (38) on the water
inlet (29).
4. The garden hose (NOT included in the scope of
delivery) can be equipped with the enclosed quick
connector (37).
5. Connect the garden hose (NOT included in the
scope of delivery) to the water inlet (29). The hose
must not be longer than 15 m.
6. Check that the hose is tightly fitted.
10.4 Self-suction from open tanks/containers and
natural bodies of water
m DANGER
• Never suck up water from a drinking water tank.
• Never suck up liquids containing solvents such as
paint thinner, petrol or oil. Solvent spray is highly
flammable, explosive and toxic.
Use the self-priming accessories (not included in
scope of delivery) consisting of:
• Suction filter
• 3 m reinforced vacuum hose
With this accessory, the device can take in water
max. 0.5 m above the water level. This can last about
1 minute.
www.scheppach.com