Scheppach HCP3000 Originalbetriebsanleitung Seite 31

Noise emission
Measured value for noise determined according to
EN 60335-2-79. The A-weighted noise level is typi-
cally:
Sound pressure level L .............90 dB(A)
pA
Uncertainty K ...................................3 dB
pA
Sound power level L ............... 105 dB(A)
WA
Uncertainty K ...................................3 dB
WA
Wear hearing protection to avoid hearing dam-
age!
Vibration emission values (vector sum of three direc-
tions) determined per EN 60335-2-79:
Hand spray gun handle
Vibration value ............................ 1.62 m/s
Hand spray gun, centre
Vibration value ............................2.27 m/s²
Uncertainty K ..............................0.85 m/s²
Note:
The vibration level specified in this instruction has
been measured based on a measurement procedure
standardised in EN 60335-2-79 and can be used for
unit comparison. The specified vibration emission
value can also be used for an initial estimation of the
exposure.
m WARNING
• The vibration level will vary depending on the use
and may in some cases be higher than the value
specified in these instructions. The vibration load
could be underestimated if the device is regularly
used in such a way. For an accurate estimation of
the vibration exposure during a given working pe-
riod, the times when the device is switched off or
running but not actually in use should also be taken
into account.
• This can significantly reduce the vibration load over
the entire working period.
8. Unpacking
• Open the packaging and carefully remove the de-
vice.
• Remove the packaging material, as well as the
packaging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport
damage. In the event of complaints the carrier must
be informed immediately. Later claims will not be
recognised.
• If possible, keep the packaging until the expiry of
the warranty period.
• Familiarise yourself with the product by means of
the operating instructions before using for the first
time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Replace-
ment parts can be obtained from your dealer.
• When ordering please provide our article number
as well as type and year of manufacture for your
equipment.
m DANGER
The device and the packaging are not children's toys!
Do not let children play with plastic bags, films or
small parts! There is a danger of choking or suffo-
cating!
m WARNING
• During unpacking, transport and storage, bear in
mind the high dead weight of the machine. These
2
activities should be carried out by two people.
• Make sure the device is level on a flat surface dur-
ing unpacking, installation and storage, operation,
testing, maintenance and when not in use.
9. Layout
9.1 Installing the bow-type handle (Fig. 3)
1. Fold the bow-type handle (1) onto the base frame
2. Tighten the star grip screw (6) using the existing
9.2 Fitting the spraying nozzle unit (Fig. 1)
1. Position the spraying nozzle unit so that the holes
2. Now fix the unit with four sleeves (5.1) and the fix-
3. To do this, first press the sleeves into the holes
9.3 Fix the transport holder to the bow-type han-
1. Slide the transport bracket (4) from above into the
9.4 Fitting the wheels (Fig. 5)
1. Slide the axle (32) through the wheel (13) from the
2. Now guide the axle (32) with wheel (13) from the
3. Repeat the process on the opposite side.
www.scheppach.com
of the device.
screws (6.1).
provided for it are on top of each other.
ing plugs (5).
provided and then secure them with the fixing
plugs (5).
dle (Fig. 4)
already pre-assembled mounting on the tubular
frame.
outside.
outside into the tubular frame (7) and secure it
with the spring split pin (33).
GB | 31