Herunterladen Diese Seite drucken

hillvert HT-MD-300B Bedienungsanleitung Seite 23

Raddumper

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
i)
Remove all adjusting tools or spanners before turning the device on. A tool or spanner left in the
revolving part of the device may cause injury.
j)
The device is not a toy. Children must be supervised to ensure that they do not play with the device.
k)
Always hold the machine with both hands. Walk, never run holding the machine and pay extra caution
while reversing it towards yourself.
2.3.
Safe device use
a)
Do not use the device if the ON/OFF switch does not function properly (does not switch the device on
and off). Devices which cannot be switched on and off using the ON/OFF switch are hazardous, should
not be operated and must be repaired.
b)
Disconnect the device from the power supply before commencement of adjustment, cleaning and
maintenance. Such a preventive measure reduces the risk of accidental activation.
c)
When not in use, store in a good ventilated place, away from children and people not familiar with the
device who have not read the user manual. The device may pose a hazard in the hands of
inexperienced users.
d)
Keep the device in perfect technical condition. Before each use check for general damage and
especially check for cracked parts or elements and for any other conditions which may impact the safe
operation of the device. If damage is discovered, hand over the device for repair before use.
e)
Keep the device out of the reach of children.
f)
Device repair or maintenance should be carried out by qualified persons, only using original spare
parts. This will ensure safe use.
g)
To ensure the operational integrity of the device, do not remove factory-fitted guards and do not
loosen any screws.
h)
When transporting and handling the device between the warehouse and the destination, observe the
occupational health and safety principles for manual transport operations which apply in the country
where the device will be used.
i)
Avoid situations where the device stops working during use due to excessive loading. This may result
in overheating of the drive elements and damage to the device.
j)
Do not touch articulated parts or accessories unless the device has been disconnected from the power
source.
k)
Do not leave this appliance unattended while it is in use.
l)
Clean the device regularly to prevent stubborn grime from accumulating.
m) The specified vibrations emission was measured using standard measurement methods. Vibrations
emissions may change if the device is used in different surroundings.
n)
If you notice a leak from the device or hoses, immediately disconnect the power supply and resolve
the defects.
o)
It is forbidden to interfere with the structure of the device in order to change its parameters or
construction.
p)
Keep the device away from sources of fire and heat.
q)
Do not overload the device. Adapt the speed to the work conditions - topography, surface and load.
r)
The engine gets very hot during operation. Do not touch the hot engine because it may cause burns.
s)
In order to avoid fire hazard, keep leaves, grass and other combustible materials away from the hot
engine and muffler.
t)
Check level and if needed add engine oil till the full marking before start using the device. Working
with too low oil can cause overheating or even damage the engine!
u)
Oil leaking from the machine should be reported to the appropriate services or comply with legal
requirements applicable in the area of use.
v)
Poisonous carbon monoxide is present in the engine exhaust. Remaining in a carbon monoxide
environment may lead to losing consciousness or even death. Do not run the engine in a closed or
poor ventilated space.
w)
Protect the engine from heat, sparks and flame. Do not smoke in the vicinity of the machine.
x)
Petrol is flammable and explosive. Before refuelling the engine should be turned off and cooled down.
y)
Warning! Risk of engine damage due to wrong fuel.
z)
The battery is live. Do not touch or cross the terminals and battery connectors. Disconnecting the
battery connectors should be carried out in the correct order.
aa) The device is not approved for use on roads in public traffic.
EN

Werbung

loading