3M 6000 Serie Bedienungsanleitung Seite 4

CLEANING INSTRUCTIONS
Clean with the 3M™ 105 Face Seal Cleaner. If disposal of parts is required this should be undertaken in accordance
with local health and safety and environmental regulations.
STORAGE AND TRANSPORTATION
These products should be stored in the packaging provided in dry, clean conditions away from sources of high
temperature and petrol and solvent vapours.
Store in accordance with manufacturer's instructions, see packaging.
] End of Shelf Life
, Maximum Relative Humidity
: Name and address of Manufacturer
Do not store outside the temperature range -10°C to +50°C or with humidity above 90%. When stored as stated, the
expected shelf life of the product is 5 years from date of manufacture.
End of shelf life (use-by) date is marked on the product and packaging. The original packaging is suitable for
transporting the product throughout the European Union.
TECHNICAL SPECIFICATION
EN 14387:2004 + A1:2008 3M gas/vapour filters generally protect against either single or multiple contaminant type(s)
and against particulates when combined with a particulate filter.
Filter Type Colour Code Type of Contaminant
A Brown
B Grey
E Yellow
K Green
Formaldehyde Olive green
AX Brown
The 6000 Series gas/vapour filters are also classified, into one of two classes, depending on their capacity to remove
contaminants from the inhaled air
Gas/Vapour Filter Classes
Gas Filter Class Maximum use concentration with 3M™ Half mask
1 10 x WEL or 1000 ppm (0.1% vol) whichever is lower
2 10 x WEL or 5000 ppm (0.5% vol) whichever is lower
* 3M assigned protection factor
WEL = Workplace Exposure Limit
Filter Type Classification
3M™ 6051/06911 A1
3M™ 6055/ 06915 A2
3M™ 6054 K1
3M™ 6057 ABE1
3M™ 6059 ABEK1
3M™ 6075
A1 &
formaldehyde
APPROVALS
These products are type approved and audited annually by either: BSI Group, The Netherlands B.V. Say Building,
John M. Keynesplein 9, 1066 EP Amsterdam, The Netherlands, Notified Body No. 2797 and / or BSI Assurance UK
Ltd, Kitemark Court, Davy Avenue, Knowlhill, Milton Keynes MK5 8PP, UK, Notified Body No. 0086. These products
meet the requirements of European Regulation (EU) 2016/425 and applicable local legislation. The applicable
European/local legislation and Notified Body can be determined by reviewing the Certificate(s) and
Declaration(s) of Conformity at www.3m.com/Respiratory/certs.
\ Temperature Range
) For Single Use Only
J Dispose in accordance with local regulations
Organic Vapours with boiling point > 65°C (with good warning properties) as specified
by the manufacturer
Inorganic Gases & Vapours (with good warning properties) as specified by the manufacturer
Acid Gases (with good warning properties) as specified by the manufacturer
Ammonia and Organic Ammonia derivatives (with good warning properties) as specified
by the manufacturer
Formaldehyde vapour
Organic vapours with boiling point < 65°C (with good warning properties) as specified by
the manufacturer
Type of Contaminant
Organic vapours, b. pt >65 degrees C (with good warning properties)
Organic vapours, b. pt >65 degrees C (with good warning properties)
Ammonia and Organic Ammonia derivatives (with good warning properties)
as specified by the manufacturer
Combination organic vapours (b.pt > 65°C (with good warning properties),
inorganic gases, acid gases
Combination organic vapours (b.pt > 65°C (with good warning properties),
inorganic gases, acid gases, Ammonia
Organic vapours, b. pt >65 degrees C (with good warning properties) &
formaldehyde up to 10 ppm
4
Maximum use concentration with 3M™ Full Face mask
20 x WEL or 1000ppm (0.1% vol) whichever is lower.
20 x WEL or 5000ppm (0.5% vol) whichever is lower.