Herunterladen Diese Seite drucken

TEUFELBERGER OD LOOP 7 MM Herstellerinformation Und Gebrauchsanleitung Seite 6

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 9
secURity / WaRninG / tRanspoRt, stoRaGe & cLeaninG
4. TO BE OBSERVED
PRIOR TO USE
Prior to every use, this product must be subject to
a visual inspection in order to verify its integrity,
readiness for use and proper functioning. Once
the product has been subject to a fall, its use must
be discontinued immediately. If the slightest doubt
remains, the product must be retired or may not be
used again until a duly compentent person, having
subjected such product to the required testing and
inspections, has approved its further use in writing.
It must be ensured that the recommendations for
use with other components be complied with: ropes
need to meet EN 1891, while carabiners need to
meet EN 362. Further PPE components must meet
the harmonized standards under the regime of
regulation (EU) 2016/425. Be sure to observe the
recommendations provided in this instructions for
use document and the specifications contained in
the "Documentation of Equipment".
The compatibility of all components in the load chain
is of critical importance.
Ensure all neighbouring components are compatible.
Ensure all components are correctly configured.
Failure to do so increases risk of serious injury or
fatality. It is the responsibility of the user that a rel-
evant and 'live' Risk Assessment is in place for the
work to be carried out which includes emergency
contingencies. A plan of rescue measures that
covers all foreseeable emergencies needs to be in
place before this product can be used. Prior to and
during use, rescue measures that can be executed
safely and effectively must be considered at all times.
5. WARNING
– If there exists only the slightest doubt about the safe
condition of the product, be sure to replace such
product immediately.
– A system that has been exposed to a fall shall be
retired, or be returned to the manufacturer or a duly
qualified repair shop for maintenance and testing.
– Snow, ice, and moisture may affect the product's
handling and strength.
– Be sure to avoid high temperatures, sharp edges,
and exposure to chemicals (e.g., acids). Rappel
slowly to prevent the generation of great heat. UV
radiation and abrasion have an adverse impact on
the rope and its strength.
6
– Knots in the rope may cause a significant reduction
of its breaking load.
6. TRANSPORT,
STORAGE AND CLEANING
Our product consists of aramid, polyester and Dynee-
ma®. Aramide and Dyneema® are not UV-stable.
Sun and chemicals attack the material and cause
its strength to decrease. In the event of reactions
such as discoloration or hardening, retire the product
for safety reasons. Furthermore, Dyneema® must
never be exposed to temperatures above 60°C.
The thimble consists of 17-4 PH stainless steel that
has been heat treated and electropolished. Do not
use this product in corrosive conditions.
When transporting the product, it must always
be protected form light and dirt and provided with
suitable packaging (moisture-repellent material that
is impervious to light).
Conditions of storage:
– Protected from light (UV radiation, welding machines ...)
– Dry and clean
– At room temperature (15 - 25 °C)
– Not in the proximity of chemicals (acids, lyes, liquids,
vapours, gases, ...) and other aggressive environments
– Protected against sharp-edged objects
Therefore, store the product dry and ventilated in
a moisture-repellent bag that is impervious to light.
For cleaning, use lukewarm water and – if available
– a rope detergent in accordance with the cleaning
instructions provided thereon. Do not use a textile
detergent. Following cleaning, rinse the product with
plenty of clear water. In any event, prior to storage
or use, allow the product to dry completely in a
natural way and not in direct sunlight, or near fires
or other heat sources.
For disinfection, use only such substances that
do not have an impact on the synthetic materials
used. Do not disinfect the product more often than
is absolutely necessary! We recommend the use
of isopropyl alcohol 70%. Apply the disinfectant
to the surface for about 3 minutes and allow the
product to dry naturally. Be sure to observe the
safety instructions for the use of the disinfectant.
If you fail to observe these provisions, you will be
putting yourself into danger!

Werbung

loading

Diese Anleitung auch für:

Od loop 7 mm t