Werbung
Drehgriff mit Vorhängeschloss abschließen
Der Drehgriff kann nur in der Schaltposition „I" (Normal) abge-
schlossen werden. Bügeldurchmesser des Vorhängeschlosses:
max. Ø 5 mm/min. Ø 4 mm.
1. Abschließvorrichtung herausziehen
2. Vorhängeschloss einhängen und verschließen. Die Schaltposi-
tion kann erst wieder nach Entfernen des Schlosses und Ein-
schieben der Abschließvorrichtung geändert werden.
Technische Daten
Isolationskoordination nach IEC 60664-1
Bemessungsspannung ....................................................................................................... AC 415 V
Bemessungs-Stoßspannung/Verschmutzungsgrad............................................................. 8 kV/3
Leistungsteil/Schaltglieder
Schaltfolge ......................................................................................................................... I - I+II - II
Kontaktbemessungsspannung U
.......................................................................................AC 400 V
e
Kontaktbemessungsstrom I
........................................................80 A (AC-21A, AC-22A, AC-23A)
e
Prospektiver Kurzschlussstrom I
...................................................................................... 50 kA eff.
cc
Bemessungsisolationsspannung U
.......................................................................................... 800 V
i
Elektrische Lebensdauer:
ATICS-BP-...-63A..............................................................................................10000 Schaltspiele
ATICS-BP-...-80A..............................................................................................10000 Schaltspiele
ATICS-BP-...-125A..............................................................................................8000 Schaltspiele
Vorsicherung:
ATICS-BP-...-63A.......................................................................................................max. 63 A gG
ATICS-BP-...-80A.......................................................................................................max. 80 A gG
ATICS-BP-4-125A.......................................................................................................max. 125 A gG
Anschlussklemmen
Nur Kupferleiter verwenden................................................................................................. ≥ 75 °C
ATICS-BP-...-63A bzw. -80A:
Leiterquerschnitt starr min./max..............................................................2,5 mm² ... 1 x 35 mm²
....................................................................................................................2,5 mm² ... 2 x 25 mm²
Abisolierlänge........................................................................................................................ 12 mm
Anzugsmoment (Kreuzschlitzschraubendreher PZ2 oder Schlitzschraubendreher 6,5 x 1,2 mm)
............................................................................................................................................... 3,5 Nm
ATICS-BP-4-125A
Leiterquerschnitt starr min./max.....................................................................10 mm² ... 70 mm²
................................................................................................................. 2 x 6 mm² ... 2 x 50 mm²
Abisolierlänge........................................................................................................................ 15 mm
Anzugsmoment (Innensechskantschlüssel 4 mm)................................................................. 4 Nm
Allgemeine Daten
Schwingungsbeanspruchung IEC 60068-2-6 (Gerät in Betrieb)............ ±1 mm/2 Hz...13,2 Hz
................................................................................................................. ±0,7 g/13,2 Hz...100 Hz
Umgebungstemperatur (Gerät in Betrieb) .......................................................... -20 °C...+40 °C
Umgebungstemperatur (bei Lagerung) .............................................................. -40 °C...+70 °C
Betriebsart..................................................................................................................... Dauerbetrieb
Einbaulage ............................................................................................................................ beliebig
Schraubbefestigung................................................................................................................ 4 x M5
ATICS-BP-SET_D00162_00_M_DEEN/04.2017
ATICS-BP-2-...-SET, ATICS-BP-4-...-SET
Lock the rotary handle with a padlock
It is only possible to lock the rotary handle in switch position
"I" (Normal) position. Padlock shackle diameter:
max. Ø 5 mm/min. Ø 4 mm.
1. Pull out locking device
2. Thread in padlock and close it. The switch position cannot be
changed until the lock has been removed and the locking
device has been pushed in.
Technical data
Insulation coordination acc. to IEC 60664-1
Rated voltage....................................................................................................................... AC 415 V
Rated impulse voltage/pollution degree............................................................................... 8 kV/3
Power unit/ switching elements
Switching sequence ...........................................................................................................I - I+II - II
Rated contact voltage U
..................................................................................................... AC 400 V
e
Rated contact current I
............................................................. 80 A (AC-21 A, AC-22 A, AC-23 A)
e
Rated conditional short-circuit current I
............................................................................50 kA eff.
cc
Rated Insulation voltage U
........................................................................................................800 V
i
Electrical endurance, number of cycles:
ATICS-BP-...-63A...................................................................................................................10000
ATICS-BP-...-80A...................................................................................................................10000
ATICS-BP-...-125A...................................................................................................................8000
Back-up fuse:
ATICS-BP-...-63A....................................................................................................... max. 63 A gG
ATICS-BP-...-80A....................................................................................................... max. 80 A gG
ATICS-BP-4-125A ......................................................................................................max. 125 A gG
Terminals
Only use copper conductors................................................................................................. ≥ 75 °C
ATICS-BP-...-63A resp. -80A:
Wire cross section, rigid min./max........................................................... 2,5 mm² ... 1 x 35 mm²
................................................................................................................... 2,5 mm² ... 2 x 25 mm²
Stripping length..................................................................................................................... 12 mm
Tightening torque (PZ2 Allen screw or slotted screwdriver 6.5 x 1.2 mm)
............................................................................................................................................... 3.5 Nm
ATICS-BP-4-125A
Wire cross section, rigid min./max..................................................................10 mm² ... 70 mm²
.................................................................................................................2 x 6 mm² ... 2 x 50 mm²
Stripping length..................................................................................................................... 15 mm
Tightening torque (Allen key 4 mm)....................................................................................... 4 Nm
General data
Vibration resistance IEC 60068-2-6 (during operation) ......................... ±1 mm/2 Hz...13.2 Hz
.................................................................................................................±0.7 g/13.2 Hz...100 Hz
Ambient temperature (device in operation) ....................................................... -20 °C...+40 °C
Ambient temperature (for storage)..................................................................... -40 °C...+70 °C
Operating mode .............................................................................................. continuous operation
Position .......................................................................................................................... any position
Screw mounting......................................................................................................................4 x M5
9
Werbung
