Ryobi RHT36B61R Bedienungsanleitung Seite 5

■
Do not operate the product in poor lighting. The
operator requires a clear view of the work area to
identify potential hazards.
■
The use of hearing protection reduces the ability to
hear warnings (shouts or alarms). The operator must
pay extra attention to what is going on in the working
area.
■
Turn off the product, remove the battery pack, and
allow both to cool down. Make sure that all moving
parts have come to a complete stop:
●
before adjusting the working position of the cutting
means
●
before servicing
●
before clearing a blockage
●
before checking, cleaning, or working on the
product
●
before changing accessories
●
before leaving the product unattended
●
before checking for damage after striking a foreign
object
●
before performing maintenance
●
whenever the product starts to vibrate abnormally
■
Do not force the product through heavy shrubbery.
This can cause the blades to bind and slow down. If
the blades slow down, reduce the pace.
■
If the product is dropped, suffers heavy impact, or
begins to vibrate abnormally, immediately turn off
the product and inspect it for damage or identify the
cause of the vibration. Any damage should be properly
repaired or replaced by an authorised service centre.
■
Operate the product only in temperatures between 0 °C
and 40 °C.
■
Store the product in a location where the ambient
temperature is between 0 °C and 40 °C.
■
Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged
periods, ensure you take regular breaks.
ADDITIONAL BATTERY SAFETY WARNINGS
■
To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse the tool,
battery pack, or charger in fluid or allow fluid to flow
inside them. Corrosive or conductive fluids, such as
seawater, certain industrial chemicals, and bleach or
bleach-containing products, etc., can cause a short
circuit.
■
Charge the battery pack in a location where the
ambient temperature is between 10 °C and 38 °C.
■
Store the battery pack in a location where the ambient
temperature is between 0 °C and 20 °C.
■
Use the battery pack in a location where the ambient
temperature is between 0 °C and 40 °C.
TRANSPORTATION AND STORAGE
■
Turn off the product, remove the battery pack, and
allow both to cool down before storing or transporting.
■
Remove all foreign materials from the product. Store
the product in a cool, dry, and well-ventilated area that
is inaccessible to children. For extra safety, store the
battery pack separately from the product. Keep the
product away from corrosive agents such as garden
chemicals and de-icing salts. Do not store the product
outdoors.
■
Fit the blade cover before storing the product or during
transportation.
■
For transportation, secure the product against
movement or falling to prevent injury to persons or
damage to the product.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries or
conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.
MAINTENANCE
■
Use only original manufacturer's replacement parts,
accessories, and attachments. Failure to do so
can cause possible injury, can contribute to poor
performance, and may void your warranty.
■
Servicing requires extreme care and knowledge
and should be performed only by a qualified service
technician. Have the product serviced by an authorised
service centre only.
■
The blades are extremely sharp. To prevent personal
injury, exercise extreme caution when cleaning,
lubricating, fitting, or removing the blade protector.
■
Remove the battery pack before adjusting, maintaining,
or cleaning the product.
■
You may make adjustments and repairs described
in this manual. For other repairs, have the product
serviced by an authorised service centre only.
■
After each use, clean the plastic parts with a soft, dry
cloth.
■
After each use, clean the debris from the blades with a
stiff brush, and then carefully apply a rust preventative
lubricant before refitting the blade protector. The
manufacturer recommends using rust preventative
lubricant spray to apply an even distribution and
reduce the risk of personal injury from contact with the
blades. For information about a suitable spray product,
check with an authorised service centre.
■
Check all nuts, bolts, and screws at frequent intervals
for proper tightness to ensure that the product is in safe
working condition. Any part that is damaged should be
properly repaired or replaced by an authorised service
centre.
5
Original Instructions
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR