Hauff-Technik HSD SSG Montageanleitung Seite 5

Standard-Ringraumdichtung
HSD SSG
Lagerung
HINWEIS!
Beschädigung durch unsachgemäße Lagerung!
Bei unsachgemäßer Lagerung können Sachschäden in erheblicher Höhe ent-
stehen.
• Standard-Ringraumdichtung vor der Montage vor Beschädigungen, Feuchte
und Verunreinigungen schützen. Es dürfen nur unbeschädigte Teile montiert
werden.
• Die Lagerung der Standard-Ringraumdichtung muss so erfolgen, dass diese kei-
nen zu niederen Temperaturen (<5 °C) und höheren Temperaturen (>30 °C) so-
wie keiner direkten Sonneneinstrahlung ausgesetzt ist.
Entsorgung
Sofern keine Rücknahme- oder Entsorgungsvereinbarung getroffen wurde, zer-
legte Bestandteile nach sachgerechter Demontage der Wiederverwertung zufüh-
ren:
• Metallische Materialreste nach den geltenden Umweltvorschriften verschrotten.
• Elastomere nach den geltenden Umweltvorschriften entsorgen.
• Kunststoffe nach den geltenden Umweltvorschriften entsorgen.
• Verpackungsmaterial nach den geltenden Umweltvorschriften entsorgen.
EN Safety Instructions and Information
Target Group
The installation may only be carried out by technical experts.
Qualified and trained individuals carrying out installation must have
• knowledge of general safety and accident prevention regulations as amended,
• knowledge of how to use safety equipment,
• knowledge of how to use hand tools and electric tools,
• knowledge of the relevant standards and guidelines for laying pipes/cables and
for backfilling utility trenches as amended,
• knowledge of the regulations and installation guidelines of the supply company
as amended,
• knowledge of the waterproof concrete directive and building waterproofing
standards as amended.
General information and intended use
In line with their intended use, our products have been developed solely for instal-
lation in buildings made of state-of-the-art materials. Insofar as no express written
confirmation has been provided by us, we do not accept any liability for any other
purposes or purposes going beyond the above.
For warranty conditions, please see our current General Terms and Delivery Condi-
tions. We explicitly draw your attention to the fact that no warranty whatsoever
applies for any subsequent damage occurring as a result of failure to follow the
installation instructions or if our products are used incorrectly or combined with
third-party products.
The Standard press seal is for sealing new pipes to be installed or pipes that have
already been laid in core drills or wall sleeves. Can be adapted to the most com-
mon cable diameters on site. The Standard press seal HSD100 SSG is suitable for
the installation and insertion of 1 cable/pipe with outer diameter 18-65 mm or
25-63 mm, 70-112 mm or 75-110 mm for HSD150 SSG, 110-162 mm or 110-
160 mm for HSD200 SSG, 159-211 mm for HSD250 SSG and 200-252 mm for
HSD300 SSG.
HSD SSG press seals are tested by FHRK according to current test guidelines
and bear the seal "FHRK Quality".
Standard press seals are not fixed settlement points or bearings and therefore
cannot absorb any mechanical forces. Any anticipated reductions must be com-
pensated for by the installation of centering guides in the conduits or core dril-
lings and/or by spacers.
Safety
This section provides an overview of all the main safety aspects for optimum pro-
tection of personnel and a safe installation process.
A failure to observe the instructions and safety information set out here may re-
sult in significant hazards.
During installation of the Standard press seal it is imperative to observe the rele-
vant professional association rules, the VDE provisions, the relevant national safety
and accident prevention regulations and your company's guidelines (work and
procedure instructions).
The fitter must wear the relevant protective clothing.
Only intact components may be installed.
The following instructions are to be observed prior to installa-
tion of the Standard press seal HSD:
WARNING!
Art. Nr.: 5090032038 Rev.: 08/2023-05-12
Risk of injury in the event of improper installation!
Improper installation can result in significant bodily harm and property da-
mage.
• Seal the underground and cable substructure well prior to laying pipes or cables
so that the latter cannot subside.
• Observe the nationally applicable laying and filling regulations for pipes and
cables.
NOTICE!
No sealing due to incorrect installation!
Improper installation can result in damage.
• For one-sided installation of the Standard press seal into core drillings, seal
from outside of building.
• Prior to installing the Standard press seal, any existing breaks or blowholes in
the cored hole have to be repaired.
• Ensure that the medium pipe is centred and horizontal in the core drilling/wall
sleeve.
• The inside of the wall sleeve must be clean and free of dust and grease.
• The respective application range is specified on the inside of the standard press
seal.
• If the Standard press seal is installed in an exposed duct, then the duct wall
must be stabilised with a clamping strap at the location of the Standard press
seal.
• The front and rear press segments must be arranged offset (except for HSD100
SSG).
• Do not lubricate the outer sealing surface of the Standard press seal with lubri-
cation. The outer sealing surface of the press seal with must be free from
grease and dry.
• The press seal is evenly pressed in as soon as the rubber can be seen and felt in
all inspection openings.
• If sealing is to be carried out on the outside of the building, a check must be
carried out before the trench is filled and all laying and connection work is
completed to see whether the rubber in all inspection openings can be seen
and felt. If this is not the case, or it is no longer possible to access the inspec-
tion openings, the torque must be checked and if necessary tightened.
• Do not use cleaning agents containing solvents to clean the Standard press
seal. We recommend using the cable cleaner KRMTX.
• For details of other accessories and further information, see www.hauff-tech-
nik.de and the technical data sheets as well as the safety data sheet.
Personnel requirements
Qualifications
WARNING!
Risk of injury in case of inadequate qualification!
Improper handling can result in significant bodily harm and property da-
mage.
• Installation may only be carried out by qualified and trained individuals who
have read and understood these instructions.
Skilled experts
Based on their specialist training, skills, experience and familiarity with the rele-
vant provisions, standards and regulations, skilled experts are able to carry out the
work assigned, independently identifying and avoiding potential hazards.
Transport, packaging, scope of delivery and storage
Safety instructions in connection with transport
NOTICE!
Damage in the event of improper transport!
Significant damage can occur in the event of improper transport.
• When unloading packaging items on delivery and in the course of in-house
transport, proceed with care and observe the symbols on the packaging.
Transport inspection
Inspect the delivery immediately on receipt for completeness and transport da-
mage. In the event of transport damage being visible from the outside, proceed as
follows:
• Do not accept the delivery or only do so subject to reservations.
• Make a note of the extent of damage in the transport documentation or de-
livery note provided by the transporter.
• Submit a claim for every defect as soon as it has been identified.
• Claims for damages can only be asserted within the applicable claim
period.
Scope of delivery
The scope of delivery of the Standard press seal HSD100 SSG, HSD150 SSG,
HSD200 SSG, HSD250 SSG and HSD300 SSG includes:
5