Operation - Cameo NANOSPOT 300 Bedienungsanleitung

7
MIC
Microphone for music control mode.
8
INFRARED SENSOR
In order to easily control the Moving Head via the supplied remote control, be sure to position the infrared interface of the remote control in
direct visual contact, at a maximum distance of 5 m from the infrared interface of the spotlight.
NOTE: The lens for focussing the projection at different distances is located in the projection head of the Moving Head. The knurled frame
provides for a better grip (clockwise rotation = remote range, counter-clockwise rotation = close range).

OPERATION

When the spotlight is properly connected to the mains, the motors are reset (Display = "InIt"). Within a few seconds, the spotlight is ready
for use and changes to the mode that was previously selected.
SELECTING THE DMX STARTING ADDRESS AND DMX MODE
Press the MODE button repeatedly until "dMX", "PrEF", "SLAV", "Soun", or "Auto" appears on the display. Now use the UP and DOWN but-
tons to select the "dMX" menu item and confirm by pressing ENTER. "Add" now appears on the display and by pressing ENTER once more,
you can select the DMX start address as desired using the UP and DOWN switches (A001 - A508). After confirming with ENTER, "SAVE" is
briefly shown on the display. To set the DMX operating mode, select the menu item "dMX", press ENTER and then use the UP and DOWN
buttons to select the menu item "ChAn". Press ENTER and use the UP and DOWN buttons to select the desired DMX mode (5Ch, 9Ch, 11Ch).
After confirming with ENTER, "SAVE" is briefly shown on the display. The synchronous control of multiple spotlights (same model) through
a DMX control unit (e.g. DMX console) can be achieved by assigning the spotlights to an identical DMX start address and DMX mode and
connecting them using DMX cables.
-> ENTER ->
<- MODE
AUTOMATIC CONTROL MODE (AUTO)
Select one of the 7 different Auto programs (Sh01 - Sh07) and their speed (SP00 - SP99). Press the MODE button repeatedly until "dMX",
"PrEF", "SLAV", "Soun", or "Auto" appears on the display. Now use the UP and DOWN buttons to select the "Auto" menu item and confirm
by pressing ENTER ("SAVE" is briefly displayed on the display). Press twice on ENTER, then use the UP and DOWN buttons to select one of
the 7 Auto programs (the last 2 digits of the display will flash). After confirming with ENTER, "SAVE" is briefly shown on the display. Now the
activated program will be shown on the display and you can use the UP and DOWN buttons to select the desired speed in the menu item.
Now, press ENTER (the last two digits on the display will flash) and using the UP and DOWN buttons, select the speed from SP00 to SP99.
After confirming with ENTER, "SAVE" is briefly displayed on the display.
-> ENTER ->
<- MODE
MUSIC CONTROL (SOUND)
Select the Music control mode, to control the Moving Head via the built-in microphone (bass pulses). Press the MODE button repeatedly until
"dMX", "PrEF", "SLAV", "Soun", or "Auto" appears on the display. Now use the UP and DOWN buttons to select the "Soun" menu item and
confirm by pressing ENTER ("SAVE" is briefly displayed on the display). Press ENTER again to select the sensitivity with which the spotlight
responds to sounds (Su00 - Su99). After confirming with ENTER, "SAVE" is briefly shown on the display.
-> ENTER ->
<- MODE
SLAVE MODE
Press the MODE button repeatedly until "dMX", "PrEF", "SLAV", "Soun", or "Auto" appears on the display. Use the UP and DOWN buttons to
select the "SLAV" menu item and confirm by pressing ENTER. Use the UP and DOWN buttons to select "YES" and confirm by pressing ENTER
6
-> ENTER ->
UP/DOWN
<- MODE
-> ENTER ->
<- MODE
-> ENTER ->
UP/DOWN
<- MODE
–
UP/DOWN
–
–
UP/DOWN
/
UP/DOWN
UP/DOWN
ENTER
UP/DOWN
–
/