DeWalt DCS397T2 Bersetzt Von Den Originalanweisungen Seite 36

EngLIsh
Saw Blades
Cat. No. Material to be cut
Rough wood
Fine wood
DCS396 Fine wood
Low density building block
Medium density building block TCT T20
Rough wood
Low density building block
DCS397
&
Medium density building block TCT T20
DCS398
Insulation materials
Celluar contrete
Prior to Operation (Fig. A)
• Mount the appropriate type of saw blade.
• Check that the tool is running properly and can perform all
its functions. Make sure that the bar
the saw blades and the housing are undamaged.
5
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. A)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the front handle
with the other hand on the rear grip handle
Switching On and Off (Fig. A)
For safety reasons the ON/OFF switch
lock-off button 2 .
1. Push the lock-off button 2
2. To run the tool, press the ON/OFF switch
as the ON/OFF switch is released the lock-off switch is
automatically activated to prevent unintended starting.
3. Always switch off the tool before removing the battery.
Sawing (Fig. A, D, E, G)
NOTICE: Do not use the saw for cutting curves or pockets.
Make sure the bar end protrudes from the workpiece.
For long, straight cuts first draw a line on the workpiece and
follow the line.
34
Recommended saw blade type
HSS DT2970
HSS DT2971
TCT DT2972
TCT T12 DT2973
DT2977
HSS DT2978
TCT T12 DT2974
DT2976
HSS DT2979
TCT 12 DT2975
6 is still straight and
4
3 .
1 is equipped with a
to unlock the tool.
. As soon
1
Make downward cuts only. Avoid cutting earth as this will blunt
the saw blades very quickly.
When using a saw horse always cut on the outside of the saw
horse arms.
1. Clamp the workpiece on one side only to prevent the bar
from jamming in the workpiece. Should this happen, ease
open the cut with wedges to relieve the strain on the blade.
Do not try to wrench the saw free.
2. Hold your D WALT power tool by the front handle
e
the rear grip handle 3 to guide the saw properly.
3. Switch the tool on before placing blade in contact with the
workpiece. Refer to Switching On and Off instruction in
this manual.

WARNING: Apply only a gentle pressure to the tool and
do not exert side pressure on the saw blade.
4. After blades have engaged the workpiece, guide the tool
back and forth in a rotating, see saw like motion as the
blades cut down through the workpiece. Refer to Figure G
5. Once cut is complete, release the trigger switch.
To increase performance and lifetime of non-painted saw
blades, regularly apply oil to the blades and in the oil holes
(every 15–30 min.). Do not lubricate painted blades.
Regularly check the saw blade setting screws
Sawing in Cellular Concrete, Low Density and
Medium Density Building Blocks (Fig. F, G)

WARNING: Cellular concrete, low density and medium
density building blocks contain lime and quartz sand.
After use to guarantee optimum performance, the saw
blades, the bar and the saw blade guide slot
thoroughly cleaned.
Dust Extraction (Fig. A)
Your saw has a built-in dust extraction port
shop vacuum to be connected.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning. Inspect tools periodically and if
damaged have them repaired by an authorized service facility.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
and
4
20
.
13
must be
9
which allows a
8