DeWalt DCS7485N Bersetzt Von Den Originalanweisungen Seite 53

6. Tighten the riving knife lock knob.
nOTE: Follow the same procedure for the riving knife.

WARNING: Before connecting the table saw to the power
source or operating the saw, always inspect the blade
guard assembly for proper alignment and clearance
with saw blade. Check alignment after each change of
bevel angle.

WARNING: To reduce the risk of serious personal injury,
DO NOT operate saw if blade assembly is not securley
clamped in place.
When properly aligned, the riving knife
the blade at both table top level, and at the top of the blade.
Using a straight edge, ensure that the blade
the riving knife 23 . With power disconnected, operate the
blade tilt and height adjustments through the extremes of
travel and insure the blade guard assembly clears the blade in
all operations.

WARNING: Correct mounting and alignment of the blade
guard assembly is essential to safe operation!
Mounting the Throat Plate (Fig. E)
1. Align the throat plate 17 as shown in figure E, and insert
the tabs on the back of the throat plate into the holes on the
back of the table opening.
2. Turn the locking screw 30
to lock the table insert in place.
3. The throat plate includes four adjustment screws which
raise or lower the throat plate. When properly adjusted, the
front of the throat plate should be flush or slightly below the
surface of the table top and secured in place. The rear of the
throat plate should be flush or slightly above the table top.

WARNING: Never use the machine without the throat
plate. Immediately replace the throatplate when worn
or damaged.
Removing the Throat Plate
1. Remove the throat plate
17
screw with a screw driver 90˚ anti-clockwise
30
2. Pull throat plate up and forward to expose the inside of the
saw. DO NOT operate the saw without the throat plate.
Fitting the Rip Fence (Fig. F)
The rip fence can be installed in two positions on the
right (Position 1 for 0 mm to 510 mm ripping, and Position 2
for 100 mm to 610 mm ripping.) and one position on the left of
your table saw.
1. Unlock the rip fence latches
2. Holding the fence at an angle, align the locator pins (front
and back) on the fence rails with the fence head
31
slots 32 .
3. Slide the head slots onto the pins and rotate the fence down
until it rests on the rails.
4. Lock the fence in place by closing the front and back
latches 19 onto the rails.
23 will be in line with
is aligned with
2
with a screw driver clockwise 90°
by turning the locking
19 .
Fixing to Workbench (Fig. A)
• The machine frame between the feet on each side is
provided with two holes 9
workbench. Use the holes diagonally.
• To improve the handling fix the machine on a piece of
plywood of min 15 mm thick.
When in use the plywood sheet can be clamped to the
workbench. This allows easier transportation of the machine, by
releasing the clamps.
ADJUSTMENTS
Blade Adjustment
Blade Alignment (Parallel to Mitre Slot)
(Fig. G)

WARNING: Cut Hazard. Check the blade at 0˚ and 45˚
to make sure blade does not hit the throat plate, causing
personal injury.
If the blade appears to be out of alignment with the mitre slot
on the table top, it will require calibration for alignment. To
realign the blade and mitre slot, use the following procedure:

WARNING: To reduce the risk of injury, turn unit
off and disconnect machine from power source
before installing and removing accessories, before
adjusting or changing set-ups or when making
repairs. An accidental start-up can cause injury.
1. Using a 5 mm hex wrench, loosen rear pivot bracket
fasteners 33 , located on the underside of the table, just
enough to allow the bracket to move side-to-side.
2. Adjust the bracket until the blade is parallel to the mitre
gauge slot.
3. Tighten the rear pivot bracket fasteners to 110–120
in-lbs (12.5–13.6 Nm).
Blade Height Adjustment (Fig. A)
The blade can be raised and lowered by turning the blade
height adjustment wheel .
6
Make sure the top three teeth of the blade are just breaking
through the upper surface of the workpiece when sawing. This
will ensure that the maximum number of teeth are removing
material at any given time, thus giving optimum performance.
Aligning Guard Assembly to Blade (Fig. H)
1. Remove the throat plate. Refer to Removing Throat Plate
under assembly and adjustments.
2. Raise the blade to full depth of cut and 0° bevel angle.
3. Locate the three small set screws
used to adjust the riving knife position.
4. Lay a straight edge on the table against two blade tips. The
riving knife should not touch the straight edge.
5. If adjustment is needed, loosen the two larger lock
screws 35 .
EnGLIsh
which allow fixing on a
33 . These screws will be
51