Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
e ) The table saw must be secured. A table saw that is not
properly secured may move or tip over.
f ) Remove tools, wood scraps, etc. from the table
before the table saw is turned on. Distraction or a
potential jam can be dangerous.
g ) Always use saw blades with correct size and shape
(diamond versus round) of arbour holes. Saw blades
that do not match the mounting hardware of the saw will
run off-centre, causing loss of control.
h ) Never use damaged or incorrect saw blade mounting
means such as flanges, saw blade washers, bolts or
nuts. These mounting means were specially designed for
your saw, for safe operation and optimum performance.
i ) Never stand on the table saw, do not use it as a
stepping stool. Serious injury could occur if the tool is
tipped or if the cutting tool is accidentally contacted.
j ) Make sure that the saw blade is installed to rotate
in the proper direction. Do not use grinding wheels,
wire brushes, or abrasive wheels on a table saw.
Improper saw blade installation or use of accessories not
recommended may cause serious injury.
Additional Safety Rules for Saw Benches
WARNING: Cutting plastics, sap coated wood, and other
materials may cause melted material to accumulate on
the blade tips and the body of the saw blade, increasing
the risk of blade overheating and binding while cutting.
•
Make sure that the blade rotates in the correct direction and
that the teeth are pointing to the front of the saw bench.
•
Be sure all clamp handles are tight before starting
any operation.
•
Be sure all blade and flanges are clean and the larger face
of the clamp washer is against the blade. Tighten the arbor
nut securely.
•
Make sure that the riving knife is adjusted to the correct
distance from the blade - maximum 8 mm.
•
Never operate the saw without the upper and lower guards
in place.
•
Do not apply lubricants to the blade when it is running.
•
Always keep the push stick in its store place when not in use.
•
Do not use the guard for handling or transportation.
•
Do not exert side pressure on the saw blade.
•
Never cut light alloy. The machine is not designed for
this application.
•
Do not use abrasive disc or diamond cutting wheels
•
Rabbeting, slotting or grooving is not allowed.
•
In case of machine failure, immediately switch the machine
off and remove the battery. Report the failure and mark the
machine in suitable form which prevents that other persons
use the defective machine.
•
When the saw blade is blocked due to abnormal feed force
during cutting, ALWAYS switch the machine off and remove
the battery. Remove the workpiece and ensure that the saw
blade runs free. Turn the machine on and start a new cutting
operation with reduced feed force.
•
NEVER attempt to cut a stack of loose pieces of material
which could cause loss of control or kickback. Support all
materials securely.
Saw Blades
•
Do not use saw blades that do not conform to the dimensions
stated in the Technical Data. Do not use any spacers to make
a blade fit onto the spindle. Use only the blades specified in this
manual, complying with EN847-1, if intended for wood and
similar materials.
•
Consider applying specially designed noise-reduction blades.
•
Do not use high steel (HS) saw blades.
•
Do not use cracked or damaged saw blades.
•
Ensure that the chosen saw blade is suitable for the material
to be cut.
•
Always wear gloves for handling saw blades and rough
material. Saw blades should be carried in a holder
wherever practicable.
Residual risks
The following risks are inherent to the use of saws:
•
injuries caused by touching the rotating parts
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
•
Impairment of hearing.
•
Risk of accidents caused by the uncovered parts of the
rotating saw blade.
•
Risk of injury when changing the saw blade with
unprotected hands.
•
Risk of squeezing fingers when opening the guards.
•
Health hazards caused by breathing dust developed when
sawing wood, especially oak, beech and MDF.
The following factors are of influence to noise production:
•
the material to be cut
•
the type of saw blade
•
the feed force
•
machine maintenance
The following factors are of influence to dust exposure:
•
worn saw blade
•
dust extractor with air velocity less than 20 m/s
•
workpiece not exactly guided
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the battery pack voltage corresponds to the
voltage on the rating plate. Also make sure that the voltage of
your charger corresponds to that of your mains.
Your D
WALT charger is double insulated in
e
accordance with EN60335; therefore no earth wire
is required.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the D
service organisation.
EnGLIsh
WALT
e
45
Werbung
Inhaltsverzeichnis
