Tips And Notes; Technical Data - Sygonix 1000 TVL Bedienungsanleitung

Connection
The camera is equipped with a connection cable with two connectors on the
end:
• BNC connector: The video signal (PAL) is available over this. Use an adapter if
you do not have a BNC cable for this connection.
• Round low-voltage socket: The external voltage/current supply is connected
to this socket. Make sure you use only a power supply unit with a stabilised
output voltage of 12 V/DC (direct current) (see also section "Technical Data" at
the end of the operating instructions).
Pay attention to the correct polarity of the connector for the power sup-
ply (inner contact = plus/+, outer contact = minus/-); otherwise the cam-
era will be damaged; loss of warranty/guarantee!
If you install and use the camera in outdoor areas, the two connectors
have to be placed in a location that is protected from humidity (in dry
indoor areas). Otherwise, the connectors will corrode.
Set the correct input channel on the display device, to display the camera image.
Afterwards, adjust the camera carefully in order to be able to monitor the desired
area.
In the dark, the IR LEDs are activated automatically. The IR light is not visible
to the human eye. Please bear in mind that because of the method used, the
image recorded at night (when the IR LEDs are activated) is not in colour, but
rather in black and white.
Cleaning
Occasionally, clean the camera from dust and dirt, especially the front screen.
Use a clean and soft cloth, moistened with water. Do not rub too hard, since
otherwise scratch marks will occur on the glass; this will cause deterioration in
the image quality!
Never point the jet of water from a garden hose or a high pressure cleaner at the
camera; never use aggressive cleaning agents.

Tips and notes

• Install the camera so that it cannot be reached without using auxiliary means.
The same applies to the connection cable. Ideally, it should be laid in a plastic
or metal pipe.
• Longer cable lengths cause deterioration in the video signal. In this case, use a
suitable amplifier.
If the cable used to supply the power is too long, the voltage will drop, and
thus the operating voltage for the camera will no longer be sufficient. This may
lead to stripes in the image or to a loss of signal. If necessary, use a cable with
a larger cross-section to reduce the voltage drop.
Disposal
The product must not be disposed of in the household waste.
Please dispose of the product, when it is no longer of use, according to
the current statutory requirements.

Technical data

Item no.
Image sensor
TV system
TV lines
Effective resolution
Video output signal
Video output
Light sensitivity
Focal length
Viewing angle
White balance
Backlight compensation
Signal-to-noise ratio (S/N ratio)
Shutter speed
Operating voltage
Power consumption
Low voltage socket
IR-LEDs
IR wavelength
IR range
IP protection class
Cable length
Ambient temperature
Weight (incl. cable and
wall bracket)
Dimensions (Ø x L),
incl. wall bracket
Legal notice
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the
capture in electronic data processing systems require the prior written approval by the editor. Reprinting,
also in part, is prohibited. This publication represent the technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE.
1359878 1359879
8.5 mm (1/3"), DIS
PAL
1000
1280 x 960 pixels (horizontal x vertical)
1.0 Vpp, 75 Ω
BNC
0.01 lux/F1.2 (or 0 lux with IR)
3.6 mm 6 mm
Horizontal 68° Horizontal 34°
Vertical 54° Vertical 44°
Automatic
Automatic
> 52 dB
1/50 ~ 1/100000 s
12 V/DC
max. 230 mA (IR on) max. 310 mA (IR on)
Polarity of round socket (5.5/2.1 mm):
outer contact = plus /+
inner contact = minus/-
24 36
850 nm
max. 20 m max. 30 m
IP65
approx. 150 cm
-20 °C to +50 °C
approx. 330 g approx. 390 g
60 x 176 mm 67.5 x 203 mm