Tips And Notes; Technical Data - Sygonix 600 TVL Bedienungsanleitung

Connection
The camera is equipped with a connection cable with two connectors on the end:
• BNC connector: The video signal (PAL) is available over this. Use an adapter, if you do
not have a BNC cable for this connection.
• Round socket: The external power supply is connected to this socket. Make sure you
only use a stabilised power supply unit with an output voltage of 12 V/DC (direct cur-
rent) (see also chapter "Technical Data" at the end of the operating manual).
Pay attention to the correct polarity of the connector for the power supply (in-
ner contact = plus/+, outer contact = minus/-), otherwise the camera will be
damaged; loss of warranty!
If you install and use the camera in outdoor areas, the two connectors may
only be placed in a location that is protected from humidity (in dry indoor ar-
eas). Otherwise, the connectors will corrode.
Set the correct input channel on the display device to display the camera image.
Afterwards, adjust the camera carefully, in order to be able to monitor the desired area.
In the dark, the IR LEDs are activated automatically. However, the LEDs are not visible
to the human eye. Please bear in mind that at night coloured image reproduction
changes into a black and white monochrome representation.
Cleaning
Occasionally clean the camera from dust and dirt, especially the front screen. Use a
dry, clean and soft cloth, moistened with water. Do not rub too hard, to avoid scratch
marks on the glass, this will cause deterioration in the image quality!
Never point the jet of water from a garden hose or a high pressure cleaner at the cam-
era; do not use aggressive cleaning agents.

Tips and Notes

• Do not use the camera in outdoor areas without using the sunscreen cover, since
this may cause overheating and damage to the camera.
• Install the camera at a height where it cannot be reached without using auxiliary
devices.
The same applies to the connection cables. Ideally, they should be run in a plastic or
metal pipe.
• Depending on the mounting location, make sure you use suitable lightning protec-
tion (e.g. installation on a pole).
• Increasing the cable lengths causes deterioration in the video signal. In this case,
use a suitable amplifi er.
If the cable used to supply the power is too long, the voltage will drop and thus, the
operating voltage for the camera will no longer be suffi cient. This may lead to stripes
in the image or to a loss of signal. If necessary, use a cable with a larger cross-section
to reduce the voltage drop.
Disposal
Electrical and electronic products do not belong to the household waste!
Please dispose of the device when it is no longer of use, according to the
current statutory requirements.
The home technology brand for the entire house. More information at www.sygonix.com

Technical Data

Image sensor: 8.5 mm (1/3"), Monalisa CCD technology
TV System: PAL
TV lines: 600
Effective resolution: 752 x 582 pixels
Video output signal: 1.0Vpp, 75 Ohm
Video output: BNC
Light sensitivity: 0.05 Lux (IR off) or 0 Lux (IR on)
(automatic switching from colour to black/white
below 0.05 Lux)
Focal length: 6mm
White comparison: Automatic (AWB)
Amplifi er control: Automatic (AGC)
Signal-to-noise ratio (S/N ratio): > 50 dB (AGC off)
Shutter speed: 1/50 - 1/120000 s
Operating voltage: 12 V/DC +/- 0.5 V/DC
Current consumption: Max. 500 mA (IR on)
Low voltage socket: Polarity of round socket (5.5/2.1 mm):
Inner contact = plus/+
Outer contact = Minus /-
IR LEDs: 36 (wavelength 850 nm)
IR range: Max. 30 m
IP protection class: IP66
Mounting: With tripod socket
Ambient temperature: -20 °C to +50°C
Ambient air humidity: 30 to 80% relative humidity
(non-condensing)
Weight: approx. 458 g incl. cable, sunscreen cover and
stand
Dimensions (W x H x D): 78 x 185 x 150mm
Legal notice
These operating instructions are a publication by Sygonix GmbH, Nordring 98a, 90409 Nürnberg (www.sygonix.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming, or the capture
in electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is
prohibited. These operating instructions represent the technical status at the time of printing. Changes in techno-
logy and equipment reserved. © Copyright 2010 by Sygonix GmbH.
Nr. 43555X - Version 11/10