Intended Use; Package Contents; Explanation Of Symbols; Safety Instructions - Sygonix 1000 TVL Bedienungsanleitung

Operating instructions
GB
DIS Surveillance Camera, 1000 TVL
Item no. 1359878 (focal length 3.6 mm)
Item no. 1359879 (focal length 6 mm)

Intended use

This camera is intended for image monitoring and protecting secluded or critical
areas (e.g., entrance areas, surveillance of underground car parks and the like).
The camera is only intended to be used with a stabilised direct current of 12 V/DC.
The product is designed for use indoors and outdoors (IP65).
Please bear in mind that it is prohibited by law to observe strangers with a cam-
era without their knowledge and consent. Observe the rules and regulations of
the country where you are using the camera.
The safety instructions must be observed at all times!
Any use other than that described above could lead to damage to this product
and involves the risk of short circuits, fire, electric shock, etc. No part of the prod-
uct may be modified or converted!
This product complies with the applicable national and European requirements.
All names of companies and products are the trademarks of the respective own-
ers. All rights reserved.

Package contents

• Camera with pre-mounted wall bracket
• Allen key
• Installation material (3 screws, 3 wall screw-plugs)
• Operating instructions

Explanation of symbols

This symbol indicates specific risks associated with handling, function
and use.
The "arrow" symbol indicates special tips and operating information.

Safety instructions

The warranty will be void in the event of damage caused by failure
to observe these safety instructions! We do not assume any liabili-
ty for any resulting damage!
We shall not accept liability for damage to property or personal in-
jury caused by incorrect handling or non-compliance with the safe-
ty instructions. In such cases, the warranty will be null and void.
• The unauthorised conversion and/or modification of the product is not
permitted for safety and approval reasons (CE). Never dismantle the
product.
• The camera is only intended to be used with a stabilised direct current
of 12 V/DC. The inner contact of the round low-voltage plug should be
plus/+, the outer contact minus/-.
• The product is not a toy and does not belong in the hands of children.
It should be operated out of the reach of children.
• The use of the surveillance camera does not replace the personal
supervision of children or people who require special assistance, but
serves only as a support to this supervision.
• The camera is suitable for use in indoor and outdoor areas (IP65). How-
ever, it must never be used in or under water, as this will destroy it.
The connector plugs on the camera's connection cable are not water-
proof or watertight and must therefore be placed in a dry indoor area.
• The camera should not be exposed to extreme temperatures, direct
sunlight, strong vibrations or heavy mechanical stress.
• Make sure that the connection cable is not pinched, kinked or dam-
aged by sharp edges.
• Do not leave packaging material carelessly lying around, as it could be-
come a dangerous plaything for children.
• Handle the product with care; it can be damaged by impacts, blows, or
accidental falls, even from a low height.
• If the camera is used with other devices (e.g., a monitor), the operating
instructions and safety notes for these devices must also be followed
without fail.
• Safe operation can no longer be assumed if:
- the device is visibly damaged,
- the device no longer works,
- the device has been stored under adverse conditions for a long time,
- it was exposed to heavy loads during transport.
• In commercial institutions, the accident prevention regulations of the
Employer's Liability Insurance Association for Electrical Systems and
Operating Facilities are to be observed.
• If you have any questions that are not answered in these operating in-
structions, please contact our technical department or another special-
ist.
Assembly
The camera should not be pointed directly towards bright sources of light
or the sun, since this will overexpose the image.
For outdoor use we recommend choosing a location that is protected
from rain (e.g., under the eaves) to prevent the formation of droplets on
the camera's front panel that will cause a distorted and unusable image.
The camera is equipped with a pre-mounted wall bracket. This is to be tightened
to a suitable place using three screws. Use appropriate screws and wall plugs,
depending on the surface.
Make sure when screwing into place or when drilling holes that cables or
wires are not damaged.
If the connection cable is to be laid so it is hidden, a correspondingly large
hole has to be drilled underneath the wall bracket, so the plug can be passed
through. The wall bracket will then cover this opening and protect the cable from
intentional damage.
Alternatively, the connection cable can be fed outwards through an opening in
the wall bracket. In this case, protect the connection cable with a suitable cable
conduit or similar.
The connection plugs are not waterproof and should be kept indoors,
otherwise they will corrode.
To align the camera, loosen the screws on the bracket using the provided Allen
key.
Place the camera in the desired position and re-tighten the screws.
A precise adjustment can be performed after putting the camera into operation,
when the camera image is displayed on the monitor.