AL-KO Solo 116 Betriebsanleitung Seite 23

Startup 116 / 118 L / 120 L
Cold start (Fig. 6) (Fig. 9)
6-1 Air filter shroud
6-2 Petrol tank
6-3 "Choke" – "Run" choke
6-4 Primer (cold-start diaphragm pump)
6-5 Starter cord
9-1 "Start" – "Stop" ignition switch
9-2 Gas lever lock
9-3 Gas lever
1. Set the ignition switch to the "Start" position (9-
1).
2. Press the gas lever lock (9-2) and hold it down;
press the gas lever (9-3).
3. Set the choke (6-3) to the "CHOKE" position.
4. Press cold-start diaphragm pump (6-4) 10
times.
5. Pull the starter cord (6-5) straight out 3-4 times
until the engine audibly starts briefly (ignition).
Pull the cord briskly with uniform force.
6. Set the choke to "RUN".
7. Pull out the starter cord until the engine starts.
8. If the engine does not start, repeat steps 1 to 7.
116 / 118 L / 120 L warm start (Fig. 6)
(Fig. 9)
1. Set the ignition switch to the "Start" position (9-
1).
2. Set the choke (6-3) to "RUN". Pull the starter
cord (6-5) – the engine starts.
Engine does not start:
„
Set the choke to the "RUN" position.
„
Pull the starter cord 5 times.
„
If the engine still does not start:
„
Wait 5 minutes and then try again with the
„
gas lever pressed down.
Refer to the "Troubleshooting" chapter.
Switching off the engine (Fig. 9)
1. Release the gas lever and let the engine idle.
2. Set the ignition switch (9-1) to "STOP".
469680_c
Caution!
The engine and cutting equipment continue to run
after being switched off – Risk of injury!
Startup 116 B / 118 B / 120
Cold start (Fig. 6) (Fig. 13)
6-1 Air filter shroud
6-2 Petrol tank
6-3 "Choke" – "Run" choke
6-4 Primer (cold-start diaphragm pump)
6-5 Starter cord
13-1 "Start" – "Stop" ignition switch
13-2 Gas lever lock
13-3 Gas lever
1. Set the choke (6-3) to the "CHOKE" position.
2. Set the ignition switch to the "Start" position
(13-1).
3. Press cold-start diaphragm pump (6-4) 10
times.
4. Pull the starter cord (6-5) straight out 2-3 times
until the engine audibly starts briefly (ignition).
Pull the cord briskly with uniform force.
5. Set the choke to "RUN".
6. Pull out the starter cord until the engine starts.
7. If the engine does not start, repeat steps 1 to 7.
116 B / 118 B / 120 warm start (Fig. 6)
(Fig. 13)
1. Set the ignition switch to the "Start" position
(13-1).
2. Set the choke (6-3) to the "RUN" position.
3. Pull the starter cord (6-5) a maximum of 6 times
– the engine starts. Keep the gas lever pressed
down until the engine runs smoothly.
Engine does not start:
„
Set the choke to the "RUN" position.
„
Pull the starter cord 5 times.
„
If the engine still does not start:
„
Wait 5 minutes and then try again with the
„
gas lever pressed down.
Refer to the "Troubleshooting" chapter.
GB
23