Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch GHO 185-LI Professional Originalbetriebsanleitung

The integrated parking rest (32) also enables a continuation
of the planing procedure following interruption at any point
on the workpiece:
– Place the power tool – with parking rest folded down –
onto the area of the workpiece that you will continue to
work on.
– Switch the power tool on.
– Shift the contact pressure onto the front of the planer
base plate and slowly slide the power tool forward (➊). In
doing so, the parking rest will swivel upwards and out of
the way (➋), meaning that the rear section of the planer
base plate is in contact with the workpiece again.
– Guide the power tool over the surface of the workpiece,
applying uniform feed (➌).
Chamfering edges (see figure P)
The V-grooves in the front of the planer base plate enable
quick and easy chamfering of workpiece edges. Select the V-
groove that corresponds to your chamfering width. Then po-
sition the planer with the V-groove onto the edge of the
workpiece and guide it along.
Groove used
None
Small
Medium
Large
Planing with the Parallel Guide (see figures K–M)
Fit the parallel guide (24) to the power tool using the fasten-
ing screw (27). Depending on the application, attach the re-
bate depth guide (31) to the power tool with the fastening
screw (30).
Loosen the locking nut (26) and set the desired rebate width
on the scale (25). Retighten the locking nut (26).
Set the desired rebate depth accordingly using the rebate
depth guide (31).
Carry out the planing procedure several times until the de-
sired rebate depth has been achieved. Guide the planer with
sideways contact pressure.

Maintenance and Service

Maintenance and Cleaning

Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
Keep the parking rest (32) clear and clean it regularly.
When the carbon brushes are worn out, the power tool
switches itself off. The power tool must be sent to the after-
sales service for maintenance; see the "After-Sales Service
and Application Service" section for addresses.
Bosch Power Tools
Changing the Drive Belt (see figures Q–R)
Unscrew the screw (8) completely and take off the belt
cover (9). Remove the worn drive belt (33).
Before fitting a new drive belt (33), clean the two belt
wheels (34) and (35).
First place the new drive belt (33) onto the small drive wheel
(35), and then press the drive belt (33) onto the large drive
belt (34), turning it by hand.
Make sure that the drive belt (33) runs exactly in the length-
ways grooves in the drive wheels (34) and (35).
Put the belt cover (9) on and tighten the screw (8).

After-Sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
Dimension a
include the 10‑digit article number given on the nameplate
(mm)
of the product.
0–2.5
Great Britain
1.5–4.0
Robert Bosch Ltd. (B.S.C.)
2.0–4.5
P.O. Box 98
3.0–5.5
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Transport
The recommended lithium-ion batteries are subject to legis-
lation on the transport of dangerous goods. The user can
transport the batteries by road without further require-
ments.
When shipping by third parties (e.g.: by air transport or for-
warding agency), special requirements on packaging and la-
belling must be observed. For preparation of the item being
shipped, consulting an expert for hazardous material is re-
quired.
Dispatch battery packs only when the housing is undam-
aged. Tape or mask off open contacts and pack up the bat-
tery in such a manner that it cannot move around in the
packaging. Please also observe the possibility of more de-
tailed national regulations.
English | 23
1 609 92A 8GN | (16.05.2023)