Safety Instructions For Planers; Product Description And Specifications; Intended Use; Product Features - Bosch GHO 185-LI Professional Originalbetriebsanleitung

18 | English
Do not expose a battery pack or tool to fire or excess-
u
ive temperature. Exposure to fire or temperature above
130°C may cause explosion.
Follow all charging instructions and do not charge the
u
battery pack or tool outside the temperature range
specified in the instructions. Charging improperly or at
temperatures outside the specified range may damage
the battery and increase the risk of fire.
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Never service damaged battery packs. Service of bat-
u
tery packs should only be performed by the manufacturer
or authorized service providers.

Safety instructions for planers

Wait for the cutter to stop before setting the tool
u
down. An exposed rotating cutter may engage the sur-
face leading to possible loss of control and serious injury.
Use clamps or another practical way to secure and
u
support the workpiece to a stable platform. Holding
the workpiece by your hand or against the body leaves it
unstable and may lead to loss of control.
Only bring the power tool into contact with the work-
u
piece when switched on. Otherwise there is danger of
kickback if the cutting tool jams in the workpiece.
Do not allow the chip ejector to come into contact with
u
your hands. You may be injured by rotating parts.
Never plane over metal objects, nails or screws. Cut-
u
ters and cutter shafts could become damaged and cause
increased vibration.
Use suitable detectors to determine if there are hid-
u
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
While working, always hold the planer in such a way
u
that the planer base plate lies flat against the work-
piece. Otherwise the planer could slip and cause injury.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
1 609 92A 8GN | (16.05.2023)
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Hold the power tool firmly with both hands and make
u
sure you have a stable footing. The power tool can be
more securely guided with both hands.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.

Intended use

The power tool is intended for planing wood-based materials
such as beams and boards while resting firmly on the work-
piece. It is also suitable for chamfering edges and for rebat-
ing.

Product features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Cutting depth scale
(2) Knob for setting the cutting depth
(insulated gripping surface)
(3) Chip ejector (either right or left)
(4) Lock-off function for On/Off switch
(5) On/off switch
a)
(6) Rechargeable battery
(7) Rechargeable battery release button
(8) Screw for belt cover
(9) Belt cover
(10) Changeover lever for chip ejector direction
(11) Planer base plate
(12) V-grooves
(13) T-handle socket spanner/Torx keys
(14) Fastening screw for clamping jaw
(15) Clamping jaw
(16) Blade head
(17) Guide groove for planer blade
(18) HSS planer blade
(19) HSS planer blade retaining clip
(20) Fastening screw for HSS planer blade retaining clip
(21) Sharpening aid for HSS planer blades
(22) Setting gauge for HSS planer blades
a)
(23) HM/TC planer blade
a)
Bosch Power Tools