Product Description And Specifications; Technical Data; Noise/Vibration Information - Bosch PSM 10,8 LI Originalbetriebsanleitung

OBJ_BUCH-1531-002.book Page 12 Monday, January 14, 2013 11:41 AM
12 | English
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for dry sanding and polishing of
wood, filler and coated surfaces. It is especially suitable for
profiles, corners or hard to reach locations.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Battery charge-control indicator / Overload indicator
2 On/Off switch
3 Battery pack *
4 Battery unlocking button *
5 Sanding sheet*
6 Sanding plate
7 Handle (insulated gripping surface)
8 Extraction outlet
9 Dust protection cap
10 Extraction adapter*
11 Vacuum hose*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.

Technical Data

Cordless Multi Sander
Article number
Rated voltage
No-load speed
No-load orbital stroke rate
Sanding sheet surface
Orbit diameter
Weight according to
EPTA-Procedure 01/2003
Please observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.

Noise/Vibration Information

Measured sound values determined according to EN 60745.
Typically the A-weighted sound pressure level of the product
is less than 70 dB(A). Uncertainty K =3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2 2
a =5.5 m/s , K=1.5 m/s .
h
2 609 006 870 | (14.1.13)
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Senior Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
PSM 10,8 LI
D-70745 Leinfelden-Echterdingen
24.10.2012
3 603 J76 9..
V= 10.8
Assembly
-1
min 11000
 Before any work on the machine itself (e. g. mainte-
-1
min 22000
nance, tool change, etc.) as well as during transport
2
cm 104
and storage, remove the battery from the power tool.
mm 1.2
There is danger of injury when unintentionally actuating
the On/Off switch.
kg 0.7
Battery Charging (see figure A)
 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The Lithium-Ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Bosch Power Tools