Product Description And Specifications - Bosch GNA 18V-16 Professional Originalbetriebsanleitung

Do not expose a battery pack or tool to fire or excess-
u
ive temperature. Exposure to fire or temperature above
130°C may cause explosion.
Follow all charging instructions and do not charge the
u
battery pack or tool outside the temperature range
specified in the instructions. Charging improperly or at
temperatures outside the specified range may damage
the battery and increase the risk of fire.
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Never service damaged battery packs. Service of bat-
u
tery packs should only be performed by the manufacturer
or authorized service providers.
Safety instructions for nibblers
This power tool is not suitable for bench-mounted use.
u
It must not be clamped into a vice or fastened to a work-
bench, for example.
Wear protective gloves during work. Sharp burrs de-
u
velop on the cut sheets; these can cause injury.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for cutting sheet metal without
deforming the material and is suitable for straight cuts, cut-
outs and narrow curves.
Bosch Power Tools
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
A)
(1) Battery
A)
(2) Battery release button
(3) On/off switch
(4) Die holder screw
(5) Handle (insulated gripping surface)
(6) O-ring
(7) Die holder
(8) Punch
(9) Die
(10) Rubber ring for knurled screw
(11) Knurled screw for die
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Nibbler
Article number
Rated voltage
No-load stroke rate n
0
Max. steel sheet cutting ca-
A)
pacity
Cutting width
Smallest curve radius
Weight according to
EPTA-Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
C)
ure during operation and
during storage
Recommended batteries
Recommended chargers
A) with reference to steel sheet of up to 400 N/mm
B) Depends on battery in use
C) Limited performance at temperatures <0 °C
Noise/Vibration Information
Noise emission values determined according to
EN 62841‑2‑8.
Typically, the A-weighted noise levels of the power tool are:
Sound pressure level 87 dB(A); sound power level
98 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
English | 11
GNA 18V-16
3 601 E29 5..
V= 18
-1
min 1400
mm 1.6
mm 5
mm 40
B)
kg 2.2–3.0
°C 0 to +35
°C −20 to +50
GBA 18V...
ProCORE18V...
GAL 18...
GAX 18...
GAL 36...
2
1 609 92A 501 | (02.12.2019)