Inhaltsverzeichnis
Werbung
Disconnect the plug from the power source and/or re-
u
move the battery pack, if detachable, from the power
tool before making any adjustments, changing ac-
cessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool
accidentally.
Store idle power tools out of the reach of children and
u
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
Maintain power tools and accessories. Check for mis-
u
alignment or binding of moving parts, breakage of
parts and any other condition that may affect the
power tool's operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained power tools.
Keep cutting tools sharp and clean. Properly main-
u
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in
u
accordance with these instructions, taking into ac-
count the working conditions and the work to be per-
formed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and
u
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Safety instructions for metal shears
This power tool is not suitable for bench-mounted use.
u
It must not be clamped into a vice or fastened to a work-
bench, for example.
Only carry out work with a fitted chip deflector. Make
u
sure that the chip deflector is not damaged or bent out
of shape. Working without a chip deflector or with a dam-
aged chip deflector poses a risk of injury. Have a dam-
aged chip deflector replaced immediately by an author-
ised after-sales service centre for Bosch power tools.
Wear protective gloves during work and pay particu-
u
lar attention to the cord. Make sure that cut sheet
parts are not bent towards your body or the cord.
Sharp burrs develop on the cut sheets; these can cause
injury or damage the cord. When necessary and while
wearing gloves, press bending sheet parts away from
your body and/or from the cord.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
Bosch Power Tools
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for cutting sheet metals without
incurring any loss from chipping. It is suitable for straight
and curved cuts.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) On/off switch
(2) Chip deflector
(3) Handle (insulated gripping surface)
(4) Fastening screw for upper cutter
(5) Upper cutter
(6) Bottom cutter
(7) Set screw for bottom cutter
(8) Fastening screw for bottom cutter
A)
(9) Hex key
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Sheet metal shears
Article number
Rated power input
Power output
No-load stroke rate n
0
Stroke speed under load
Max. steel sheet cutting ca-
A)
pacity
Smallest curve radius
Weight according to
EPTA-Procedure 01:2014
English | 9
GSC 75-16
3 601 E00 5..
W
750
W
400
-1
min
5200
-1
min
4000
mm
1.6
mm
35
kg
1.7
1 609 92A 50F | (04.12.2019)
Werbung
Inhaltsverzeichnis
