Specifications; Additional Safety Rules - Makita JS1600 Betriebsanleitung

ENGLISH
1 Lower blade
2 Loosen
3 Upper blade
4 Upper blade securing bolt
5 Hex wrench
6 Thin washers
7 Blade holder
8 Tighten

SPECIFICATIONS

Model
Max. cutting capacities
Steel up to 400 N/mm
Steel up to 600 N/mm
Steel up to 800 N/mm
Aluminum up to 200 N/mm
Min. cutting radius ......................................... 30 mm
Strokes per minute .......................................... 4,000
Overall length ............................................... 230 mm
Net weight ....................................................... 1.7 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed
Safety instructions.

ADDITIONAL SAFETY RULES

1. Hold the tool firmly.
2. Secure the workpiece firmly.
3. Keep hands away from moving parts.
4. Edges and chips of the workpiece are sharp.
Wear gloves. It is also recommended that you
put on thickly bottomed shoes to prevent
injury.
5. Do not put the tool on the chips of the work-
piece. Otherwise it can cause damage and
trouble on the tool.
6. Do not leave the tool running. Operate the tool
only when hand-held.
7. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
8. Do not touch the blade or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
Explanation of general view
9 No gap allowed
0 Yoke
q Lower blade positioning screw
w Lock-off lever in the
FREE position
e Switch lever (Paddle switch)
r Lock-off lever in the
LOCK position
2
...................... 1.6 mm/16 ga
2
...................... 1.2 mm/18 ga
2
...................... 0.8 mm/22 ga
2
............... 2.5 mm/13 ga
9. Avoid cutting electrical wires. It can cause
JS1600
serious accident by electric shock.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Blade inspection
Before using the tool, check the blades for wear. Dull,
worn blades will result in poor shearing action, and
the service life of the tool will be shortened.
Rotating or replacing blades
Important:
Always be sure that the tool is switched off and
unplugged before rotating or replacing the blades.
Both the upper and lower blades have four cutting
edges on each side (the front and back). When the
cutting edge becomes dull, rotate both the upper and
the lower blades 90° to expose new cutting edges.
When all eight edges are dull on both the upper and
lower blades, replace both blades with new ones.
Each time blades are rotated or replaced, proceed as
follows.
Remove the blade securing bolts with the hex wrench
provided and then rotate or replace the blades.
(Fig.1)
Some tools have one or more thin washers between
ENB011-2
the upper blade and the blade holder. Be sure to use
the same number of thin washers when reassem-
bling. (Note: No thin washers are used for the lower
blade.) (Fig. 2)
To secure the upper blade, tighten the upper blade
securing bolt with the hex wrench. Press up on the
upper blade while tightening it. (Fig. 3)
After securing the upper blade, be sure that there is
no gap left between the upper blade and the bevelled
surface of the blade holder. (Fig. 4)
When installing the lower blade onto the yoke, the
lower blade should be pressed against the yoke so as
to be contacting the bevelled portions A and B of the
yoke and the tip C of the lower blade positioning
screw while you tighten the lower blade securing bolt.
There must be no clearance between A, B and C
during installation. (Fig. 5 & 6)
Note:
The lower blade positioning screw is factory-
assembled. Do not tamper with it.
t Lock-off lever
y Gauge for stainless: 1.2 mm
u Gauge for mild steel: 1.6 mm
i Workholder
o Limit mark
p Screwdriver
a Brush holder cap
5