Specifications - RIDGID 300 Compact Bedienungsanleitung

Cutter
Rear
Chuck Jaw
Centering
Handwheel
Device
REV/OFF/FWD
(2/0/1)
Switch
Warning
Label
Motor
Warning
Foot
Cover Hand
Label
Switch
Hold
Figure 1 – 300 Compact Threading Machine

Specifications

Parameter
Pipe Threading Capacity
(Nominal Pipe Size)
Bolt Threading Capacity
(Actual Stock Diameter)
LH Threads
Rated Motor Power (HP)
Motor Type
Electrical Information
Operating Speed
Controls
Front Chuck
Rear Centering Device
Die Heads
Cutter
Reamer
Oil System
Weight (Unit with Die Head)
Sound Pressure
(L )* ........................................< 84.6 dB(A), K=3
PA
Sound Power (L )*....................................... < 89.6 dB(A), K=3
WA
* Sound measurements are measured in accordance with a standardized test per
Standard EN 62481-1.
- Sound emissions may vary due to your location and specific use of these tools.
999-998-098.08_REV C
Quick Opening
Die Head
Reamer
Carriage
Front
Hand
Hold
Oil
Carriage
Chip Tray Drain
Handwheel
300 Compact Threading Machine
/ to 2 inch (3 to 50 mm)
1
8
/ to 2 inch (6 to 50 mm)
1
4
Yes (units with REV only)
1/2 HP (0.37 kW)
Universal Motor, Single Phase
36 RPM
110-120V, 50/60 Hz, 14 AMP
220-240V, 50/60 Hz, 8 AMP
1700 W
36 RPM (52 RPM version available)
Rotary Type REV/OFF/FWD (2/0/1) switch and ON/OFF foot
switch,
Some units use an OFF/ON Rocker Switch in place of the Rotary
Switch.
Hammer-Type with replaceable
Rocker-Action Jaw Inserts
Scroll operated, rotates with Chuck
See RIDGID Catalog for available Die Heads
Model 360, / " - 2" Full Floating,
1
8
Self Centering Cutter
Model 344, /
1
Reservoir Capacity 3.2 qt (3 l), with integrated Gerotor Pump,
adjustable flow rate
141 lb (64 kg)
300 Compact/1233 Threading Machines
Rear
Centering
Device
Motor
Cover
Warning
Label
Foot
Switch
Figure 2 – 1233 Threading Machine
52 RPM
110-120V, 50/60 Hz, 18 AMP
2100 W
" - 2" Reamer
8
- Daily exposure levels for sound need to be evaluated for each application and
appropriate safety measures taken when needed. Evaluation of exposure levels
should consider the time a tool is switched OFF and not in use. This may signifi-
cantly reduce the exposure level over the total working period.
REV/OFF/FWD
(2/0/1)
Chuck Jaw
Switch
Handwheel
Warning Chip
Carriage
Label Tray
1233 Threading Machine
/ to 3 inch (3 to 80 mm)
1
8
/ to 2 inch (9,5 to 50 mm)
3
8
No
1/2 HP (0.37 kW)
Universal Motor, Single Phase
110-120V, 50/60 Hz, 15 AMP
220-240V, 50/60 Hz, 8 AMP
1700 W
36 RPM
Rotary Type REV/OFF/FWD (2/0/1) switch
and ON/OFF foot switch,
Some units use an OFF/ON Rocker Switch in
place of the Rotary Switch.
Hammer-Type with replaceable
Rocker-Action Jaw Inserts
Scroll operated, rotates with Chuck
See RIDGID Catalog for available Die Heads
Model 763, ⁄ " - 3",
1
4
Self Centering Cutter
Model 743, ⁄ " - 3", 5-Fluted Reamer
1
4
Reservoir Capacity 3.2 qt (3 l), with
integrated Gerotor Pump, adjustable flow rate
165 lb (75 kg)
No. 763
Cutter
Die
Head
No. 743
Reamer
Oil
Drain
Carriage
Handwheel
5
5