Electrical Safety - Husqvarna DC 655 Bedienungsanweisung

• Make sure that rough surfaces, for example welded
seams or floor joints, do not stop the product.
• Make sure that there are no cables or hoses in the
operation direction of the product.
• Make sure that there is sufficient airflow in the work
area.
• Make sure that there are no flammable liquids in the
work area.
• This appliance is not suitable for use in classified
(hazardous) locations, to pick up dusts or liquids of
high explosion risk, nor mixtures of combustible dust
with liquids.
• Do not pick up anything that is burning or smoking,
such as cigarettes, matches, or hot ashes.
• Do not use to pick up flammable liquids, such as
gasoline, or use in areas where flammable vapors
may be present.

Electrical safety

WARNING:
shocks from electrical products. Do not use
the product in bad weather conditions. Do
not touch lightning conductors and metal
objects. Always use the product as given in
this operator's manual to prevent injury.
WARNING:
with RCD (residual-current device). An RCD
decreases the risk of electrical shock.
WARNING:
unprotected parts in the power unit. Always
disconnect the power plug before you open
the door to the electrical box.
WARNING:
on the product for purposes specified in the
instructions.
CAUTION:
the product or generator must be sufficient
and constant to make sure that the motor
operates without problems. Incorrect voltage
causes the power consumption and the
temperature of the motor to increase until
the safety circuit releases. The dimension
of the power cord must agree with national
and local regulations. The dimension of the
mains socket must agree with the amperage
for the electrical socket and extension cable
of the product.
If the power mains has higher system
resistance, short voltage drop can occur
when the product is started. This can
2061 - 002 - 19.04.2023
There is always a risk of
Always use a power supply
High voltage. There are
Only use the socket outlets
The power supply from
influence the operation of other products, for
example flicker on the lights.
• The power plug must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of electric
shock.
• Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Make sure that the power, fuse and mains voltage
are the same as the voltage shown on the rating
plate of the product.
• Always stop the product before you disconnect the
power plug.
• Make sure that the ON/OFF switch is in OFF position
before the product is connected to the power supply.
• Always disconnect the power plug during a long
product stop.
• Do not use the product if the supply cord or power
plug is damaged. If the supply cord is damaged, it
must be replaced by the manufacturer, its service
agentor similarly qualified persons in order to avoid
a hazard. A damaged power cord can cause serious
injury and death.
• Use the power cord correctly. Do not use the power
cord to move, pull or disconnect the product. Pull the
power plug to disconnect the power cord. Do not pull
the power cord.
• Only operate the product on dry surfaces.
• Keep the product away from rain. Water that goes
into the product increases the risk of electrical shock.
• Always disconnect the power cord before you
connect or disconnect the connection for the motor
cable and the electrical enclosure.
• In order to avoid a hazard due to inadvertent
resetting of the thermal cut-out, this appliance
must not be supplied through an external switching
device, such as a timer, or connected to a circuit that
is regularly switched on and off by the utility.
• Make sure that the power supply for the product is
supplied by separate transformers that are used for
industrial purpose only.
Grounded product instructions
WARNING:
result in electrical shock. Speak to an
approved electrician if you are not sure if
your mains outlet is correctly grounded.
Do not do modifications to the power plug
from its factory specification. If the power
plug or power cord is damaged or must be
replaced, speak to your Husqvarna service
agent. Obey local regulations and laws.
Incorrect connection can
7