Rotary Hammer Safety Warnings; Safety Instructions For All Operations; Additional Safety Warnings - Makita HR2470 Betriebsanleitung

ENGLISH
(Original instructions)
1 Switch trigger
2 Lock button
3 Lamp
4 Reversing switch lever
5 Quick change chuck for SDS-
plus
6 Change cover line
7 Change cover
8 Spindle
9 Quick change drill chuck
SPECIFICATIONS
Model
Capacities
Concrete
Tungsten-carbide tipped bit ..................................... 24 mm
Core bit .................................................................... 54 mm
Diamond core bit (dry type) ..................................... 65 mm
Steel ........................................................................... 13 mm
Wood .......................................................................... 32 mm
–1
No load speed (min ) ................................................... 0 – 1,100
Blows per minute ........................................................... 0 – 4,500
Overall length ................................................................ 370 mm
Net weight...................................................................... 2.9 - 3.3 kg
...........................................................
Safety class
• Due to our continuing program of research and
development, the specifications herein are subject to
change without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s).
The lightest and heaviest combination, according to
EPTA-Procedure 01/2014, are shown in the table.
Intended use
The tool is intended for hammer drilling and drilling in
brick, concrete and stone as well as for chiselling work.
It is also suitable for drilling without impact in wood,
metal, ceramic and plastic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General power tool safety warnings
WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Explanation of general view
10 Action mode changing knob
11 Rotation only
12 Hammering only
13 Grip base
14 Side grip
15 Loosen
16 Tighten
17 Teeth
18 Protrusion
19 Bit shank
HR2470/HR2470F
/II

ROTARY HAMMER SAFETY WARNINGS

Safety instructions for all operations

1.
2.
ENE043-1
3.
ENF002-2
Safety instructions when using long drill bits
with rotary hammers
1.
GEA010-2
2.

Additional safety warnings

1.
2.
20 Bit grease
21 Bit
22 Chuck cover
23 Depth gauge
24 Dust cup
25 Blow-out bulb
26 Chuck adapter
27 Keyless drill chuck
28 Sleeve
29 Ring
HR2470T/HR2470FT
24 mm
54 mm
65 mm
13 mm
32 mm
0 – 1,100
0 – 4,500
394 mm
3.0 - 3.3 kg
/II
Wear ear protectors. Exposure to noise can cause
hearing loss.
Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
Hold the power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory may contact hidden wiring
or its own cord. Cutting accessory contacting a "live"
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
Always start drilling at low speed and with the bit
tip in contact with the workpiece. At higher
speeds, the bit is likely to bend if allowed to rotate
freely without contacting the workpiece, resulting in
personal injury.
Apply pressure only in direct line with the bit
and do not apply excessive pressure. Bits can
bend, causing breakage or loss of control, resulting in
personal injury.
Wear a hard hat (safety helmet), safety glasses
and/or face shield. Ordinary eye or sun glasses
are NOT safety glasses. It is also highly
recommended that you wear a dust mask and
thickly padded gloves.
Be sure the bit is secured in place before
operation.
GEB243-1
5