Rotary Hammer Safety Warnings; Additional Safety Rules - Makita HR2460 Betriebsanleitung

ENGLISH
(Original instructions)
1 Switch trigger
2 Lock button
3 Lamp
4 Reversing switch lever
5 Action mode changing knob
6 Grip base
7 Side grip
8 Loosen
SPECIFICATIONS
Model
Capacities
Concrete
Tungsten-carbide tipped bit ............................. 24 mm
Core bit............................................................ 54 mm
Diamond core bit (dry type) ............................. 65 mm
Steel ................................................................... 13 mm
Wood .................................................................. 32 mm
–1
No load speed (min )........................................ 0 – 1,100
Blows per minute................................................ 0 – 4,500
Overall length ...................................................... 362 mm
Net weight ..................................................... 2.8 – 3.2 kg
.......................................................
Safety class
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s).
The lightest and heaviest combination, according to
EPTA-Procedure 01/2014, are shown in the table.
Intended use
The tool is intended for hammer drilling and drilling in
brick, concrete and stone.
It is also suitable for drilling without impact in wood,
metal, ceramic and plastic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General power tool safety warnings
WARNING: Read
instructions, illustrations
provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fire
and/or serious injury.
Save all warnings and instructions for future refer-
ence.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
4
Explanation of general view
9 Tighten
10 Teeth
11 Protrusion
12 Bit shank
13 Bit grease
14 Bit
15 Chuck cover
16 Depth gauge
HR2460/HR2460F
ENE042-1
ENF002-2
GEA010-2
all safety warnings,
and specifications

ROTARY HAMMER SAFETY WARNINGS

Safety instructions for all operations
1. Wear ear protectors. Exposure to noise can cause
hearing loss.
2. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
3. Hold the power tool by insulated gripping sur-
faces, when performing an operation where the
cutting accessory may contact hidden wiring or
its own cord. Cutting accessory contacting a "live"
wire may make exposed metal parts of the power
tool "live" and could give the operator an electric
/II
shock.
Safety instructions when using long drill bits with
rotary hammers
1. Always start drilling at low speed and with the bit
tip in contact with the workpiece. At higher
speeds, the bit is likely to bend if allowed to rotate
freely without contacting the workpiece, resulting in
personal injury.
2. Apply pressure only in direct line with the bit
and do not apply excessive pressure. Bits can
bend, causing breakage or loss of control, resulting
in personal injury.

ADDITIONAL SAFETY RULES

1. Wear a hard hat (safety helmet), safety glasses
and/or face shield. Ordinary eye or sun glasses
are NOT safety glasses. It is also highly recom-
mended that you wear a dust mask and thickly
padded gloves.
2. Be sure the bit is secured in place before opera-
tion.
3. Under normal operation, the tool is designed to
produce vibration. The screws can come loose
easily, causing a breakdown or accident. Check
tightness of screws carefully before operation.
4. In cold weather or when the tool has not been
used for a long time, let the tool warm up for a
while by operating it under no load. This will
loosen up the lubrication. Without proper warm-
up, hammering operation is difficult.
5. Always be sure you have a firm footing. Be sure
no one is below when using the tool in high loca-
tions.
6. Hold the tool firmly with both hands.
7. Keep hands away from moving parts.
8. Do not leave the tool running. Operate the tool
only when hand-held.
17 Dust cup
18 Blow-out bulb
19 Keyless drill chuck
20 Chuck adapter
21 Sleeve
22 Ring
GEB243-1